Grizzly EXTREME G0513X2 Скачать руководство пользователя

Страница: 87 / 100

G0513 Series Bandsaws (Mfd. Since 08/22)

-85-

BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

G0513A40 Labels

304

303

302

301

312

311

307

306

• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

grizzly.com

***

COLOR CODES

GRIZZLY GREEN

PANTONE 568C

DANGER

PANTONE 485 C or RAL 3001

PANTONE 151 C or RAL 2005

WARNING

GRIZZLY LOGO RED

PANTONE 711C or RAL 3020

Note:

Labels marked with ### must have individual

letters/numbers. DO NOT print with clear background.

• Scale= 1:1

(unless otherwise noted)

• Labels MUST be made of

chemical-resistant material

G0513 Machine Labels

(08/29/18)

Note:

Labels marked *** have changed since last sent.

###

310

315

310

314

305

313

316

308

grizzly.com

Motor: 2 HP, 110V/220V, 1-PH, 60 Hz
Prewired Voltage: 220V
Amp Draw: 9.5A at 220V; 19A at 110V
Table Size: 17" x 17"
Blade Speeds: 1700 & 3500 FPM
Blade Length Range: 130-1/2" – 131-1/2"
Blade Width Range: 1/8" – 1"
Max. Cutting Width Left of Blade: 16-1/4"
Max. Cutting Height: 12-1/8"
Table Tilt: 10˚L ⁄ 45˚R
Weight: 266 lbs.

MODEL G0513A40

ANNIVERSARY EDITION

17" 2 HP BANDSAW

Date

Mfd. for Grizzly in Taiwan

Specifications

WARNING!

To reduce risk of serious injury when using this machine:

1. Read and understand owner’s manual before operating.
2. Never touch a moving blade and always keep hands out of

blade path or “line of cut.”

  3. Always wear approved eye protection and respirator.
  4.  Only plug power cord into a grounded outlet.
  5.  Only remove jammed cutoff pieces when blade is stopped.
  6.  Use push stick or holding jig to cut small or narrow pieces.
  7.  Turn motor OFF and disconnect power before changing

blades, making adjustments, or servicing.

8. Maintain proper adjustment of blade tension, tracking, guides,

and thrust bearings.

  9.  Keep upper guide adjusted to just clear the workpiece.
10.  Hold workpiece firmly against table to maintain control.
11.  Only run saw with wheel covers closed and guards in place.
12.  Never reach under table while blade is in motion.
13.  DO NOT wear loose clothing, gloves, jewelry, or other articles

that can get entangled. Tie back long hair and roll up sleeves.

14.  DO NOT expose to rain or use in wet locations.
15.  DO NOT operate under influence of drugs or alcohol.
16.  Prevent unauthorized use by children or untrained users;

restrict access or disable machine when unattended.

G0513A40

G0513 Series

Generic Labels

(7/12/13)

• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material

FOR GRIZZLY MACHINES ONLY!

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com.

WARNING!

EYE/LUNG INJURY

HAZARD!

Always wear safety

glasses and a

respirator when

using this machine.

INJURY/SHOCK

HAZARD!

Disconnect power

before adjustments,

maintenance, or

service.

INJURY HAZARD!

Do not open door
while machine is
connected to power
or blade is in motion.

G0513 Series

Generic Labels

(7/12/13)

• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material

FOR GRIZZLY MACHINES ONLY!

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com.

WARNING!

EYE/LUNG INJURY

HAZARD!

Always wear safety

glasses and a

respirator when

using this machine.

INJURY/SHOCK

HAZARD!

Disconnect power

before adjustments,

maintenance, or

service.

INJURY HAZARD!

Do not open door
while machine is
connected to power
or blade is in motion.

304

G0513 Series

Generic Labels

(7/12/13)

• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com.

WARNING!

EYE/LUNG INJURY

INJURY/SHOCK

INJURY HAZARD!

Do not open door
while machine is
connected to power
or blade is in motion.

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual, call

(800) 523-4777 or go to

www.grizzly.com.

G0513 Series

Generic Labels

(7/12/13)

• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material

FOR GRIZZLY MACHINES ONLY!

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL!

Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

To reduce risk of death

or serious injury, read

manual BEFORE using

machine.
To get a new manual,

call (800) 523-4777 or

go to www.grizzly.com.

WARNING!

EYE/LUNG INJURY

HAZARD!

Always wear safety

glasses and a

respirator when

using this machine.

INJURY/SHOCK

HAZARD!

Disconnect power

before adjustments,

maintenance, or

service.

INJURY HAZARD!
Do not open door
while machine is
connected to power
or blade is in motion.

G0513 Series

Generic Labels

• 1:1 Sizing (Labels are
actual size)
• Labels must be made of
oil-resistant material

DO NOT REPRODUCE OR CHANGE THIS ARTWORK

Grizzly will not accept labels changed without approval.

artwork changes are required, contact us immediately at [email protected].

309

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

301

P0513A40301

MACHINE ID LABEL

309

P0513A40309

40TH ANNIVERSARY LABEL

302

P0513A40302

MODEL NUMBER LABEL

310

P0513A40310

ELECTRICITY LABEL

303

P0513A40303

GRIZZLY NAMEPLATE

311

P0513A40311

READ MANUAL LABEL

304

P0513A40304

DO NOT OPEN DOOR LABEL

312

P0513A40312

EYE LUNG HAZARD LABEL

305

P0513A40305

DISCONNECT POWER LABEL

313

P0513A40313

BLADE TENSION SCALE LABEL

306

P0513A40306

TOUCH-UP PAINT, GRIZZLY GREEN

314

P0513A40314

GUIDE POST ADJUST LABEL

307

P0513A40307

TOUCH-UP PAINT, GRIZZLY BLACK

315

P0513A40315

SAW TENSION LABEL

308

P0513A40308

GRIZZLY.COM LABEL

316

P0513A40316

GUIDE POST LOCK LABEL

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes

off or becomes unreadable, the owner of this machine MUST replace it in the original location

before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

Содержание EXTREME G0513X2





































































































Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Похожие инструкции для EXTREME G0513X2

Бренды по названию

Популярные бренды

Grizzly EXTREME G0513X2, Руководство пользователя

Результаты поиска

Содержание EXTREME G0513X2

Отзывы:

Похожие инструкции для EXTREME G0513X2

Бренды по названию

Популярные бренды