background image

 
 

Model 7250 Power Pinner Bench Hand Welder 

12 

WARRANTY 

 

 
All Gripnail Fastening Equipment is thoroughly inspected and tested before leaving the factory.  
Gripnail Corporation warranties its equipment to be free from defects in workmanship and mate-
rials under normal and proper use for a period of  one (1) year from date of sale to original end 
purchaser. 
 
The warranty does not apply when repairs or attempted repairs have been made by persons other 
than Gripnail Corporation’s authorized service personnel, or where it is determined by our ser-
vice personnel that the equipment has been subjected to misuse, negligence or accident.  If it is 
determined that any fasteners other than those manufactured by Gripnail have been used in this 
machine or tool, the warranty is terminated. 
 
This warranty is not effective unless equipment is properly registered with the factory through 
the use of warranty information card prior to use.  Gripnail Corporation shall not be liable for 
contingent damages or delays caused by defective materials or any other means beyond our con-
trol. 

 
 

Gripnail Customer Service Department 

Gripnail Corporation 

97 Dexter Road 

East Providence, Rhode Island 02914 

Phone: (401) 216-7900 

Fax: (401) 438-8520 

Email: [email protected] 

Website: www.gripnail.com 

Содержание 7250













Отзывы: