manualshive.com logo in svg

Grindmaster Cecilware CL100N Series, Руководство оператора

Поделиться
Скачать
Grindmaster Cecilware CL100N Series Скачать руководство пользователя страница 11

Coffee Urns

Cecilware

®

11

Component Tests

Water Inlet Valve Test

1. Turn power OFF. If the water level rises inside a

partially filled tank, the Water Inlet Valve is leaking.  

2. Disconnect wires from the Water Inlet Valve coil and

connect a 2 wire line cord to the terminals. Plug it
into a 115V outlet. If water flows in and stops when
you pull it out, the Valve is working fine. Repeat this
test a few times. The problem may be in the Probe
or Water Level Control Board. 

3. If the water does not flow in when the cord is

plugged into an electrical outlet, the Solenoid coil
may be damaged, opened or the valve may have an
obstruction preventing the water from flowing in. 

4. Clean or replace it.

Dual Probe Test

If lack of water persists, check the probe as follows:

1. Turn on the power and water supply. Check inside

the tank to make sure the water is below the Probe.
Pull the BLUE wire and terminal OFF the Probe rod.  

2. If water still does not flow after the wire is

disconnected from the Probe, the problem may be
in the Solid State Dual Level Control Board.

3. If water starts flowing into the tank, the Probe may

be grounded, due to excessive liming. Check with
Ohm meter.

4. Clean or replace probe.

Dual Probe Liquid Level Controller Test

Check the Controller as follows:
1. Make sure there is power input to the Controller at

the terminals AC1 & AC2. Your voltmeter should
read 115 Volts. It should read the same at terminals
AC1 & FILL when the water level is low. This is the
output power to actuate the coil of the Solenoid
Valve to open it. 

2. The lack of voltage at terminals AC1 & L-LEVEL or

H-LEVEL indicates that the Controller is not working
properly.

3. Make sure all wire connections are tight, including

ground.

4. If after this, the Controller is still failing to open the

Water Inlet Valve, replace it.

Maintenance (continued)

Hose Nut Assembly

Blue

WARNING: SHOCK AND BURN HAZARD

To prevent electric shock and burn hazard, all tasks
described in this section are to be performed by a
trained and qualified service technician.

WARNING: SHOCK HAZARD

Disconnect power before attempting any electrical
repairs.

Содержание CL100N Series































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды