Grifco Fire Shutter Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 16

background image

7

INSTALLATION

Mounting plate slots allow the chain tension to
be adjusted through vertical movement of the
opener (see Left)

Mounting the Unit (continued)

Room needed for safe chain operation

Mounting Plate slots

Clear path for manual chain to hang downward

Mounting Plate

Drive Chain

The unit must be mounted accurately so that the
drive sprocket lines up with the shutter platewheel.
There is only a small allowance for adjustment of the
drive sprocket position on the output shaft. Fit the
correct length of drive chain around the drive
sprocket and platewheel.

«
...
5
6
7
8
9
...
»

Содержание Fire Shutter

















Отзывы:

Нет отзывов

Похожие инструкции для Fire Shutter

Бренд: Hankscraft Runxin Страницы: 53

Бренд: Gardigo Страницы: 8

Бренд: Gardigo Страницы: 19

Бренд: Eaton Страницы: 8

Бренд: OJ Electronics Страницы: 8

Бренд: OJ Electronics Страницы: 112

Бренд: OJ Страницы: 17

Бренд: IDTECK Страницы: 12

Бренд: Banner Страницы: 2

CGLine+ Web Controller

Бренд: Eaton Страницы: 28

Бренд: Nemesis Страницы: 6

Q Module WFZ16.Ox

Бренд: QUNDIS Страницы: 24

Бренд: Atmel Страницы: 12

Бренд: Nibe Страницы: 92

Бренд: Planar Страницы: 162

Бренд: THK Страницы: 134

Бренд: Eaton Страницы: 108

Бренд: Carrier Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды