Grifco C10A Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 20

background image

6

PLANNING

The C10A Wall Controller is available with optional enclosures and Key Switch operations.
Please select the most appropriate controller for the application.

Installing the controller

The controller is connected to the MCB via a low voltage control cable provided within the controller enclosure. Using the conduit
entries provided (also enclosed) run the cable through conduit. Be sure not to cut or damage the cable and therefore cause
installation issues and void warranty.

CAUTION: Do not force the controller cable! Excess stretching and manipulation can cause cable failure.

Plug ends must not be gripped with pliers.

To  connect  the  controller  to  the  eDrive  +2.0  opener,  identify  the  most  appropriate  entry  of  the  MCB  enclosure  for  your
installation. Open the MCB enclosure and fit the conduit fitting, allowing enough cable to reach the controller (RJ45) socket.  Place
the opposing end of the controller cable through the conduit entry of the controller enclosure and pull through any excess cable.
Plug the RJ45 end into the socket located within the controller assembly. Use the space provided within the controller enclosure
to neatly coil any excess cable.

Note: If the supplied 6m controller cable is not long enough for your installation, use a Grifco® Controller Extension Kit,
available from your local dealer or Chamberlain (P/N ESK01).

WARNING

Install the controller in a position where the door is visible. Failure to do so may result in serious injury or death to persons

trapped beneath the door. Minimum mounting height is 1.5 metres from floor level.

Part
Number

Description

Enclosure Material

2.0 Wall Controller (Basic Operation)

C10A-4

Standard 2.0 Controller (supplied standard with all 2.0 openers)

Plastic

C10AW-4

Standard 2.0 Controller (IP55)

Plastic

C30A

Standard 2.0 Controller

metal

2.0 Wall Controller (Key Switch Operation)

C21B

2.0 Controller with basic Key Isolator (On-Off)

Plastic

C41B

2.0 Controller with basic Key Isolator (On-Off)

Metal

C23B

2.0 Controller with “Lock-it-Well” Isolator (On-Off)

Plastic

C43B

2.0 Controller with “Lock-it-Well” Isolator (On-Off)

Metal

C21D-2

2.0 Controller with Multi-Mode Isolator (Off-Auto– Auto/Manual)

Plastic

C41D-2

2.0 Controller with Multi-Mode Isolator (Off-Auto– Auto/Manual)

Metal

INSTALLATION

«
...
4
5
6
7
8
...
»

Содержание C10A





















Отзывы:

Нет отзывов

Похожие инструкции для C10A

Бренд: Bard Страницы: 8

Бренд: Bardiani Valvole Страницы: 35

Бренд: Samson Страницы: 52

Бренд: YOKOGAWA Страницы: 2

ALICAT SCIENTIFIC PC

Бренд: Halma Страницы: 2

ALICAT SCIENTIFIC PCD

Бренд: Halma Страницы: 46

ServeRAID-MR10is

Бренд: IBM Страницы: 94

ServeRAID-4 Ultra160 Series

Бренд: IBM Страницы: 20

8271 Nways Ethernet LAN Switch

Бренд: IBM Страницы: 6

Бренд: IBM Страницы: 86

Бренд: IBM Страницы: 205

Бренд: IBM Страницы: 28

Ecomot300 AC2630

Бренд: IFM Electronic Страницы: 111

Бренд: Parker Страницы: 54

Бренд: RAM Страницы: 71

Бренд: Universal Remote Страницы: 20

Бренд: Data Signs Страницы: 23

Бренд: SYCLOPE electronic Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды