manualshive.com logo in svg

GridConnect WI232 Plus, Быстрый старт

Поделиться
Скачать
GridConnect WI232 Plus Скачать руководство пользователя страница 15

 

 

1-13 

Finally, select 

the ‘

Save

’  option in the Permanent Config: field.. 

At this point, the xPICO-WiFi is configured and ready to access data with a Terminal Emulator program like 
Teraterm.  

1.6 6 Configuring Teraterm  

Teraterm is a free terminal program that can be configured for a TCP/IP or Serial connection. To test the 
configuration settings of the WI232 Plus, you can use two instances of Teraterm. One will make a TCP/IP 
connection to the WiFi side and the other will make a connection to the Serial side. You can test both 
settings from a single laptop.  

Connect a serial cable from your laptop port to the serial cable on the WI232 Plus module.  

Start up the Teraterm terminal program to open the following window:  

Note: the settings shown are for demo purposes.  

 

Select the 

TCP/IP

 radio button and configure the window as shown below. The Host IP address was the one 

shown in the Status window. The TCP port# was selected in the Tunnel/Accept section. 

 

Click OK and the terminal window appears with the IP address and port settings in the top bar. 

Содержание WI232 Plus


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды