Greystone Energy Systems GDT Series Скачать руководство пользователя страница 15

Страница: 15 / 18

Page 15

<MENU>

Press to advance to next menu item

Use <UP> or <DOWN> to select a parity value of None, Odd or

Even. The default ModBus parity is None.

Use <UP> or <DOWN> to select a baud rate of 9600, 19200,

38400, 57600, 76800 or 115200 as required. The default baud

rate is 9600.

ModBus

Parity N

BaudRate

9600

42. PARITY

41. BAUD RATE

Only if

Modbus

model

Only if

Network

model

<MENU>

Press to advance to next menu item

Use <UP> or <DOWN> to toggle the stop bits between 1 and 2.

The default ModBus stop bits is 1.

Use <UP> or <DOWN> to set the CRC value to A001 (CRC-16

reverse), 1021 (CITT), 8005 (CRC-16), or 8408 (CITT reverse). The

default CRC polynomial is OxA001.

Use <UP> or <DOWN> to change the value from Minimum

to 50, 100, 150, 200, 250, 300 or 350mS. The factory default

ModBus slave response delay is Minimum

(minimum delay

means just more than 3.5 character time delays, 4ms for 9600 baud

rate, for example)

ModBus

Stop 1

ModBus

CRC A001

ModBus

Del MIN

43. STOP BITS

44. CRC

45. DELAY

<MENU>

Press to advance to next menu item

<MENU>

Press to advance to next menu item

<MENU>

Press to advance to next menu item

<MENU>

Press to advance to next menu item

Only if

CO Sensor

is installed

This item allows zero calibration of the CO sensor. Ensure the

sensor is in clean air. Press and hold the <UP> key for 3 seconds

to initiate the calibration process. When the calibration is

complete, the display will indicate DONE. Then press <MENU>

to advance to the next selection. A CO Zero Calibration Counter

is incremented every time this step is performed. The CO ReCal

timer is reset whenever this step is performed.

CO Zero

Cal GO

CO Zero

Cal DONE

46. ZERO

CALIBRATION

then

This item allows span calibration of the CO sensor. Apply 250

ppm CO gas to the sensor. Press and hold the <UP> key for 3

seconds to initiate the calibration process. When the calibration

is complete, the display will indicate DONE. Then press

<MENU> to advance to the next selection. A CO 250 Calibration

Counter is incremented every time this step is performed. The

CO Re-Cal timer is reset whenever this step is performed.

CO 250

Cal GO

CO 250

Cal DONE

47. SPAN

CALIBRATION

then

<MENU>

Press to advance to next menu item

IN-GE-GDTXXX-06

Содержание GDT Series



















Результаты поиска

Содержание GDT Series

Отзывы:

Бренды по названию

Популярные бренды

Greystone Energy Systems GDT Series, Руководство по установке

Результаты поиска

Содержание GDT Series

Отзывы:

Бренды по названию

Популярные бренды