manualshive.com logo in svg

GreenWorks 2000902, Руководство пользователя, Страница: 9 / 38

Поделиться
Скачать
GreenWorks 2000902 Скачать руководство пользователя страница 9

9

Some of the following symbols may be used on this product. Please study them and learn 

their meaning. Proper interpretation of these symbols will allow you to operate the product 

SYMBOLS

SYMBOLS

DESIGNATION

EXPLANATION

V

Volts

Voltage

A

Amperes

Current

Hz

Hertz

Frequency (cycles per second)

W

Watts

Power

hrs

Hours

Time

no

No Load Speed

Rational speed, at no load

Class II Construction Double-insulated construction

/ min

Per Minute

Revolutions, strokes, surface speed, orbits etc., per minute.

Lithium-Ion Battery 

Recycling

Designates that this tool is in compliance with  

Lithium-Ion battery recycling program requirements.

Safety Alert Symbol Precautions that involve your safety.

Read the Operator’s 

Manual

To reduce the risk of injury, user must read and  

understand operator’s manual before using this product.  

Eye and Head 

Protection

Wear eye and head protection when operating this 

equipment.

Gloves

Wear non-slip, heavy-duty protective gloves when 

handling the chain saw and the blade.

 

Safety Footwear

Wear non-slip safety footwear when using this 

equipment.

Kickback

DANGER! Beware of kickback.

Operate With Two 

Hands

Hold and operate the saw properly with both hands.

One Handed

Do not operate the saw using only one hand.

Bar Nose Contact

Avoid bar nose contact.

Keep Bystanders 

Away

Keep all bystanders at least 50 ft. (15 m) away.

Wear Ear protection Wear ear protection when operating this equipment.

Содержание 2000902







































Отзывы:

Нет отзывов