GreenTec RM 232 Скачать руководство пользователя страница 42

Страница: 42 / 44

Rotary Mulcher RM 232

Troubleshooting

Problem

Cause

Solution

Valve or leaky
engine

Return oil pressure too high

Check oil pressure.
Jammed/squeezed/broken hoses -
especially on the return side.

Drain oil pressure too high

Check oil pressure. Free flow to tank.
Jammed/squeezed/broken hoses -
especially on the return side.

Return hose not attached
correctly or fallen off

Attach correctly or put it on again.
If necessary, change the quick
release coupling gaskets

Overheating

Tool speed is wrong

Check the rotation speed on the tool.

Oil level wrong

Check oil level.

Oil type wrong

Empty the tank and fill up with with
the correct oil.

Blades are blocked

Remove branch residue and the like

Air humidity too high

Install a cooler. Decrease working
speed.

Hydraulic fails

Low oil level

Fill up with oil to correct level.

Oil leak in the pressure hose

Check the machine for leaks.

Oil pump section filter is
clogged

Replace filter insert.

The branches are
"frayed"

Branches are bigger than
recommended

Do not exceed the mulchers
recommended cutting lengths.

Work is done in winter

Work within the hedge's growing
season. Drive slower, adjust speed
to the conditions.

Cutting result
crooked/chopped

Rotor bearings defective

Replace bearings.

Rotor damaged/crooked

Replace rotor and drive only in suited
material.

Driving speed too fast

Adjust speed to the work.

The tool is shaky

Rotor damaged/crooked

Replace rotor or axle.

Weight of blades uneven due
to wear

Grind the blades to have the same
weight or replace them.

A blade is jammed

Release it.

A blade is broken

Replace the blade.

Clippings hurled
towards the cabin

The tool is turning so that
rotors are facing the cabin

Only drive with the tool as
recommended by GreenTec.

A rotor stops

Belt tension incorrect

Adjust to the right tension.

Содержание RM 232













































Результаты поиска

Содержание RM 232

Отзывы:

Похожие инструкции для RM 232

Бренды по названию

Популярные бренды

GreenTec RM 232, Руководство пользователя

Результаты поиска

Содержание RM 232

Отзывы:

Похожие инструкции для RM 232

Бренды по названию

Популярные бренды