Greenlee 43180 Скачать руководство пользователя страница 8

Страница: 8 / 26

43180 Overhead Circular Saw

Greenlee / A Textron Company

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Specifications

(cont’d)

Hydraulic Power Source

Do not exceed the following hydraulic power source

maximums:

•  Hydraulic flow:  22.7 l/min (6 gpm)
•  Pressure relief:  138 bar (2000 psi)
•  Back pressure:  13.8 bar (200 psi)
Failure to observe this warning could result in severe

injury or death.

Type of Hydraulic System

........................

Open-center or

closed-center

Flow

Minimum .........................................

15.1 l/min (4 gpm)

Recommended ...............................

18.9 l/min (5 gpm)

Maximum ........................................

22.7 l/min (6 gpm)

Filtration ............................................

10 micron (nominal)

Operating Pressure
Minimum .........................................

121 bar (1750 psi)

Maximum ........................................

138 bar (2000 psi)

Pressure Relief Setting

........................

138 bar (2000 psi)

Back Pressure (maximum)*

..................

13.8 bar (200 psi)

* 13.8 bar (200 psi) is the maximum agreed stan-

dard back pressure for the HTMA (Hydraulic Tool

Manufacturers Association). Greenlee Utility tools will

operate satisfactorily at this standard.

1. Maximum hydraulic fluid temperature must not

exceed 60 °C (140 °F). A sufficient oil cooling

capacity is needed to limit the hydraulic fluid

temperature.

2. Hydraulic flow must not exceed 22.7 l/min (6 gpm).

Install a flow meter in the return line to measure the

rate of hydraulic flow before using the tool.

3. Pressure relief valve setting must not exceed

138 bar (2000 psi) at the tool’s maximum flow.

Locate the pressure relief valve in the supply circuit

to limit excessive hydraulic pressure to the tool.

Hydraulic Schematic

FILTER

(10 micron)

COOLER

RELIEF

VALVE

138 bar

(2000 psi)

CONTROL

VALVE

FLOW METER

TOOL

RESERVOIR

PUMP

POWER SOURCE

Recommended Hydraulic Fluids

Electric shock hazard:
When using this tool near ener-

gized electrical lines, select and

maintain the hydraulic fluid to meet

the minimum dielectric standards

required by your safety department.
Failure to observe this warning could

result in severe injury or death.

Use any non-detergent, petroleum-based hydraulic

fluid which meets the following specifications or HTMA

specifications.

S.U.S. @
38 °C (100 °F)

.............................................140 to 225

99 °C (210 °F)

.......................................... 40 minimum

Flash Point ................................

170 °C (340 °F) minimum

Pour Point .................................

–34 °C (–30 °F) minimum

Содержание 43180



























Результаты поиска

Содержание 43180

Отзывы:

Бренды по названию

Популярные бренды

Greenlee 43180, Инструкция по эксплуатации

Результаты поиска

Содержание 43180

Отзывы:

Бренды по названию

Популярные бренды