Greenlee 1800 Mechanical Bender Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 14

Greenlee 1800 Mechanical Bender Скачать руководство пользователя страница 8

Greenlee / A Textron Company

8

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

1800 Mechanical Bender

Special Bending Information

Laying Out Bends

The following illustrations and instructions show the most common bends. See the Special Bending Information

Chart for precise bending dimensions.

Stubs

Y

HEIGHT

MARK

ANGLE

1.  Select the size and type of conduit. Determine the height of stub and the angle of bend.
2.  Find the chart that corresponds to the size of conduit selected in Step 1.
3.  Under the column labeled ANGLE, find the angle of bend. Find the intersection of row Y and the appropriate

column H. The number at this intersection is the dimension Y. Place the bending mark Y inches from the end of

the conduit.

4. See the Operation section of this manual.

Offset

An offset is used to route the conduit around an obstruction. To make an offset, two equal bends are required. The

distance between the two bends is the center-to-center distance. This is represented by L1 in the bending tables.

Offsets: Controlling the Start of the First Bend

(use this method when working past an obstruction)

L1

LENGTH – X

LENGTH

HEIGHT

START OF

FIRST

BEND

BENDING

MARK 1

BENDING

MARK 2

ANGLE

1. Select the size and type of conduit. Measure the height of the obstruction and the distance labeled LENGTH.

Determine the angle to be used.

2. Find the chart that corresponds to the size of conduit selected in Step 1.
3. To the right of the size and type of conduit, find the dimension labeled X. Subtract X from LENGTH. Place the

first bending mark this distance from the end of the conduit.

4. Under the column labeled ANGLE, find the angle of bend. Find the intersection of the L1 row and the appropriate

HEIGHT column. The number at this intersection is the dimension L1. Place the second bending mark L1 inches

from the first bending mark.

5. See the Operation section of this manual.

«
...
6
7
8
9
10
...
»

Содержание 1800 Mechanical Bender















Отзывы:

Нет отзывов