It is essential to tap SAVE “ ” button to save current step when programming each step.
If a program is merely 1 step,tapping COMPLETE “ ” will save the program which eliminates the use of
SAVE“ ”button.
A recipe that has been validly programmed will replace previous DIY program.
The machine may beep to indicate of failure if any programming goes wrong. Such failure does not affect or
replace existing recipe program.
To ensure its long service life, the machine is preset at the workload of no more than 30 minutes working
continuously.
The machine will verify the duration of new program is no longer than 15 minutes. Otherwise programming
fails whilst the machine beeps twice to indicate failure.
A recipe program is composed of 18 steps at most. The display will show “FULL” to indicate the full limit for
steps.(The 18th step is still programmable but adding extra step is impossible)
For easier use,the 1st step is forbidden to be at speed “0”. (A failure to set speed other than “0” will disable
1st step to be saved.)
Default recipe for DIY button is ICE CRUSH.
If the last step fails to be saved without tapping SAVE “ ” button when programming multiple steps, the
program will only include previous steps excluding the last step after tapping COMPLETE “ ”.
Under DIY editing mode a continuous no-operation for 30 seconds will dim the display. A continuous no-op-
eration for 3 minutes will exit DIY editing mode. The steps that have been programmed will not be saved.
Under DIY editing mode removing the jar will turn off the machine meanwhile exiting editing mode.
A valid DIY program will be stored into memory of the machine and last for 20 years whether machine is
connected to power or not.
Repeatable read-write cycles for DIY programming are 100,000 times.
Warning!
11
GREENIS
POWER BLENDER
GREENIS
POWER BLENDER 12
Other important precautions
：
USE PRECAUTIONS
USE PRECAUTIONS
About measuring cup, lid and seal ring
：
Rotating Blades Can Cause Severe Injury.
DO NOT put hands, spatulas, utensils, etc. into the jar while the blender is running or while the jar
is on the base.
Different tampers and lids match with different jar styles, types and sizes. Use the tamper that is
supplied with your jar and blender.
Place the measuring cup onto the lid (place measuring cup through the central opening of lid
and twist clockwise to fasten) and place the lid onto the jar securely.
Make sure that the machine is not running before putting the tamper.
The seal ring around the lid is detachable. When cleaning remove seal ring from the lid to
thoroughly clean away residues stuck inside the seal ring and the lid.
Stirring ingredient that is fermentative or dry (little water content) for a long time may cause over-heating
and thus trigger overheating protection mechanism built inside the motor. Therefore please start with low
speed and change to high speed if the ingredients are thick or rather dry. If it's still difficult to stir, please
shut down the power, reduce amount of ingredients or add liquid to decrease viscosity.
The motor will stop working when overheated. Unplug the blender and cool down the motor for 45
minutes in a drafty place or in front of a fan.
During the operation, make sure the lid and measuring cup are fastened tightly, in case the food inside
would splash out and cause injuries.
During the operation, DO NOT put hand, any tool (like spoon), or other hard object into the blender jar, in
case of any danger or damage.
When making hot drinks (like soybean milk, rice paste, pottage, etc.), make sure the lid and measuring cup
are fastened tightly, and set the speed from low speed to high speed.
When making sauces (like almond paste, jam, peanut butter or sesame paste, etc.), stuffing, or shell grains,
the volume of ingredients must be among 3 cups to 5 cups; DO NOT operate continuously for a long time,
in case there will be scorched flavor because of overheating. Too many ingredients may also cause
overload, triggering motor’s over-temperature protection.
Please place liquid and soft ingredients first before hard ones like ice cubes.
DO NOT remove the jar until the blades come to a full stop. Otherwise it may cause damages to drive
socket.
Please stop the machine once smelling any scorching smell. It may be caused by overload of ingredients or
the fact blades and drive socket are not fully engaged.
It is recommended to operate the machine no more than 30 minutes at a time.
Always disconnect the appliance from the supply if it is left unattended and before assembling, disassem-
bling or cleaning.
This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
Make sure the lid is securely placed on the jar if tamper is to be used. Shut down the blender
before placing tamper through the hole of lid, in case of food splashing to cause injures.
DO NOT use other implements to replace the tamper if it is missing, which may otherwise cause
injuries. Please contact local dealer to purchase replacement part.
