background image

* Sizes are in inches. 

12x12

 

48x12 

12x48 

24x24 

36x36

 

AMCA 5.3 Pressure drop 

SMd-302M

5D

6D

5D

D

4 (W) (H)

3.14

Velocity (fpm)

Pressure Drop        

(in. wg)

Velocity (fpm)

Pressure Drop        

(in. wg)

Velocity (fpm)

Pressure Drop        

(in. wg)

Velocity (fpm)

Pressure Drop        

(in. wg)

Velocity (fpm)

Pressure Drop        

(in. wg)

500

0.01

500

0.01

500

0.01

500

0.01

500

0.01

1000

0.06

1000

0.02

1000

0.02

1000

0.02

1000

0.04

1500

0.13

1500

0.06

1500

0.05

1500

0.06

1500

0.10

2000

0.23

2000

0.10

2000

0.09

2000

0.10

2000

0.18

2500

0.37

2500

0.16

2500

0.14

2500

0.16

2500

0.29

3000

0.53

3000

0.23

3000

0.21

3000

0.24

3000

0.42

3500

0.73

3500

0.32

3500

0.29

3500

0.33

3500

0.57

4000

0.95

4000

0.42

4000

0.38

4000

0.43

4000

0.74

24 in. x 24 in. (610mm x 610mm)

36in. x 36 in. (914mm x 914mm)

12in. X 48 in. (305mm x 1219mm)

48 in. x 12 in. (1219mm x 305mm)

12 in. x 12 in. (305mm x 305mm)

Greenheck Fan Corporation certifies that the 

model SMD-302M shown herein is licensed 
to bear the AMCA Seal. The ratings shown 
are based on tests and procedures performed 
in accordance with AMCA Publication 511 
and comply with the requirements of the 

AMCA Certified Ratings Programs. The 
AMCA Certified Ratings Seal applies to air 

performance ratings only.

R

Содержание Exhaust Fan SMD-302M








Отзывы: