background image

Utility and Centrifugal Fans

15

®

Unit Start-Up

Visual Inspection of Equipment

The equipment type and arrangement should be 
verified as ordered at once when it arrives at the 
jobsite. When a discrepancy is found, the local 
representative must be notified immediately so that 
corrective action may be investigated, also verify 
electrical conformance to specifications. Unauthorized 
alterations and unauthorized backcharges will not be 
recognized by manufacturer.

After the unit has been assembled, installed and all 
utilities have been hooked up, the unit is ready for 
operation.

Check

Before starting the unit, check the following:

1.  Confirm that building supply voltage matches the 

voltage for which the unit is wired.

2.  Check all piping and wiring penetrations made by 

contractors for water tightness. All penetrations 
must be made watertight to prevent water 
damage to the unit and building.

3.  Rotate the fan wheel manually to be sure that it 

is free to operate. Remove any dirt or debris that 
may have accumulated during installation.

4.  Check the fan bearing setscrews for tightness.

5.  Check alignment of sheaves and V-belts. See 

Maintenance section.

6.  Inspect all fasteners to ensure that none have 

loosened during shipment.

7.  Check flex coupling for proper alignment and 

connect between motor shaft and fan shaft 
(direct drive).

8.  Check all guarding to ensure that it is securely 

attached and not interfering with rotating parts.

9.  Check all electrical connections for proper 

attachment.

10.  Check housing and ductwork, if accessible, 

for obstructions and foreign material that may 
damage the fan wheel.

11.  Fill drainage piping trap.

WARNING

Disconnect and secure to the 

OFF

 position all 

electrical power to the fan prior to inspection 
or servicing. Failure to comply with this safety 
precaution could result in serious injury or death.

DANGER

Pour écarter les risques de blessure grave ou 
de mort, débrancher et verrouiller l’alimentation 
électrique en position « Arrêt » avant tout contrôle 
ou entretien.

Additional Steps for Initial Start-Up

1.  Check for proper wheel 

rotation by momentarily 
energizing the fan. 
Access to view the 
wheel can be gained 
through the blower 
housing access panel.

One of the most frequently encountered problems 
are motors that are wired to rotate the wheel in 
the wrong direction. This is especially true with 
3-phase installations where the motor will run in 
either direction, depending on how it has been 
wired. To reverse rotation of a 3-phase motor, 
interchange any two of the three electrical leads. 
Single phase motors can be reversed by changing 
internal connections as described on the motor 
label or wiring diagram. 

2.  Fans with multi-speed motors should be checked 

on low speed during initial start-up.

3.  Check for unusual noise, vibration or overheating 

of bearings. Refer to the “Troubleshooting” section 
of this manual if a problem develops.

4.  Grease may be forced out of the bearing seals 

during initial start-up. This is a normal self-purging 
feature for the type of bearing used on this 
product.

Model USFD - Three-phase

This unit ships with the variable frequency drive (VFD) 
preprogrammed based on selected performance. No 
additional programming is required.

1.  To operate, turn disconnect on and allow VFD to 

power up.

2.  Once VFD display is shown, press 

LO/RE

 button 

which will switch control from remote to local.

3.  If necessary, use vertical arrows to scroll through 

display screens to find frequency reference 

F

.

4.  Frequency should be programmed from factory. 

To balance system (by adjusting frequency), press 

Enter

 and use vertical arrows and 

Reset / >

 button 

until desired frequency is achieved. Press 

Enter

 to 

set frequency.

5.  Press 

Run

 to start fan.

6.  If additional adjustment is required, press 

Stop

 and 

repeat steps 3-4.

Содержание CSW

























Отзывы: