Gree GRS-1.5/D150ANbA-K Скачать руководство пользователя страница 73

Страница: 73 / 81

GREE AIR SOURCE HEAT PUMP WATER HEATER SERVICE MANUAL

Attachment: Mapping Table of the Temperature
Sensor Resistance and Temperature

The following tables lists the mapping relationship between resistance of different temperature

sensors and temperature. The resistance for different temperature can be queried during maintenance.

Note: Due to variance in measuring method and temperature sensing, the sensor resistance may

deviate at ±5°C.

Mapping between the temperature

and resistance of 15 kΩ (outdoor ambient temperature

sensor)

Temperature (°C)

Resistance (kΩ)

Temperature (°C)

Resistance (kΩ)

-20

144

2.523

-19

138.1

2.439

-18

128.6

2.358

-17

121.6

2.28

-16

115

2.205

-15

108.7

2.133

-14

102.9

2.064

-13

97.4

1.997

-12

92.22

1.933

-11

87.35

1.871

-10

82.75

1.811

-9

78.43

1.754

-8

74.35

1.699

-7

70.5

1.645

-6

66.88

1.594

-5

63.46

1.544

-4

60.23

1.497

-3

57.18

1.451

-2

54.31

1.408

-1

51.59

1.363

49.02

1.322

46.8

1.282

44.31

1.244

42.14

1.207

40.09

1.171

38.15

1.136

36.32

1.103

34.58

1.071

32.94

1.039

31.38

100

1.009

29.9

101

0.98

Содержание GRS-1.5/D150ANbA-K


















































































Результаты поиска

Содержание GRS-1.5/D150ANbA-K

Отзывы:

Похожие инструкции для GRS-1.5/D150ANbA-K

Бренды по названию

Популярные бренды

Gree GRS-1.5/D150ANbA-K, Руководство по обслуживанию

Результаты поиска

Содержание GRS-1.5/D150ANbA-K

Отзывы:

Похожие инструкции для GRS-1.5/D150ANbA-K

Бренды по названию

Популярные бренды