Gree GRS-1.5/D150ANbA-K Скачать руководство пользователя страница 16

Страница: 16 / 81

GREE AIR SOURCE HEAT PUMP WATER HEATER SERVICE MANUAL

4 Operation Instructions

4.1 On/Off Setting

The unit will be started or stopped by pressing the ―On/Off ‖ button.

Note: After energization and under normal communication, the LCD will display the water temperature,

time, and hot water volume (for models with dual temperature sensor) under both On and Off states of the

unit. It means the Off state if the LCD does not display the running mode, as shown in the following figure.

4.2 Common Modes Setting

In the On state of the unit, press the

MODE

button to switch the operation modes in the following

sequence:

HOTWATER

SAVE

PRESET

NIGHT

The HOTWATER mode is shown in the following figure.

4.3 Special Modes Setting

If the heat pump of a water heater equipped with an electrical heater is faulty, users can press and

hold

MODE+RAPID

for 5s in any mode under the state to enter the

E-HEATER

mode.

Note: The E-HEATER mode can be used only when the heat pump is faulty. In this case, contact the

Содержание GRS-1.5/D150ANbA-K


















































































Результаты поиска

Содержание GRS-1.5/D150ANbA-K

Отзывы:

Похожие инструкции для GRS-1.5/D150ANbA-K

Бренды по названию

Популярные бренды

Gree GRS-1.5/D150ANbA-K, Руководство по обслуживанию

Результаты поиска

Содержание GRS-1.5/D150ANbA-K

Отзывы:

Похожие инструкции для GRS-1.5/D150ANbA-K

Бренды по названию

Популярные бренды