Great Wall hover, Руководство по обслуживанию

Страница: 124 / 425

Automatic transmission-48
solenoid
valve
Condition Transmission operation
1
Opened
always
1st-Gear replaces 2nd-Gear; 4th-Gear replaces 3rd-Gear. It causes the car form the G ear shift of 1
→
1
→
4
→
4 when accelerate form static. The transmission stay longer time in Gear; worse 1
→
4
shift feeling.
Closed always
2nd-Gear replaces 1st-Gear; 3rd-Gear replaces 4th-Gear. It causes the car form the G ear shift of 2
→
2
→
3
→
3 when accelerate form static. It is said that starts form 2nd-Gear.
2 Closed always
4th-Gear replaces 1st-Gear; 3rd-Gear replaces 2nd-Gear. It causes the car form the G ear shift of 2
→
2
→
3
→
3 when accelerate form static. That is saying that start form 4th-Gear.
Opened
always
2nd-Gear replaces 3rd-Gear; 1st-Gear replace 4th-Gear.
It cause the car is shifted form 1st-Gear to 2nd-Gear, then from 2nd-G ear to Gear when accelerate
form static. It will feel the transmission is in free gear position after 2
→
1 Gear shift.
1&2
Opened
always
Can not realize the reverse gear; only has 1st-Gear operation.
3 Closed always Following shifts are bad. (2
→
3 is worst ):1
→
3, 1
→
4, 2
→
3, 2
→
4, 4
→
2, 4
→
1
Opened
always
Following gear shifts are worse: 3
→
4, 4
→
3, 3
→
2
。
It may cause the gear slide when the hydraulic torque converter is locked.
4 Closed always
Following gear shifts are worse:
1
→
2, 1
→
3, 1
→
4, 2
→
3, 2
→
4, 3
→
1, 3
→
2, (including manual) 3
→
4, 4
→
1, 4
→
3
Opened
always
Following gear shifts are worse: (1
→
2 is worst) 2
→
4, 3
→
2 It may cause the gear slide when
the hydraulic torque converter is locked.
6 Closed always The line pressure is high always.
Opened
always
The line pressure is low always. So it cause the slide between gears. The clutch C1 and brake belt
B1 will be burned.
7 Closed always The hydraulic torque converter is without lock.
Opened
always
The hydraulic torque converter is locked in 3rd-Gear and 4th-Gear. It cause the car generates the
vibration in low-speed status.
Table 6.1.2 Operation of transmission when ON/OFF solenoid valve is faulty
Mechanical detection
1.Inspection of transmission on car
It should process the following detections before disassemble the transmission:
process the on-road drive test to determine the failure cause .(according to requirement)
Detect the standard of transmission fluid. (refer to 7.2.1)
Ensure the transmission fluid in not overheated. (Normal color and smell)
Detect the failure information.
Check the battery terminal and grounding for corrosion or loose.
The engine speed is within the specified value in manual.
Check the cooling system for normal operation.
All power supply and plug wires is tight and not loose.
Check the transmission fluid, ensure the oil pan is without other martial material or pollutant.
2. Oil leakage detection
It should wash the polluted part of the transmission before select the oil leakage part, then drive the car.
When detect the leakage part of the rear servo system, it should lift the car by lifter firstly, then switch the gear to reverse
gear within 10s.
When detect the leakage part of front servo system, it should lift the car by lifter firstly, then switch the gear to gear-2
(winter mode).
The time switched to 2nd-Gear should be no more than 10s to avoid the oil in the torque converter is overheated.
3. FAQ table