background image

WARRANTY

Great Planes

®

Model Manufacturing Co. guarantees this kit to be free from defects in both material and workmanship at the date of

purchase. This warranty does not cover any component parts damaged by use or modification. In no case shall Great Planes’ liability
exceed the original cost of the purchased kit. 
Further, Great Planes reserves the right to change or modify this warranty without notice.

In that Great Planes has no control over the final assembly or material used for final assembly, no liability shall be assumed nor
accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled
product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this
kit immediately in new and unused condition to the place of purchase.

To make a warranty claim send the defective part or item to Hobby Services at the address below:

Hobby Services

3002 N. Apollo Dr., Suite 1

Champaign, IL 61822 USA

Include a letter stating your name, return shipping address, as much contact information as possible (daytime telephone number, fax
number, e-mail address), a detailed description of the problem and a photocopy of the purchase receipt. Upon receipt of the package
the problem will be evaluated as quickly as possible.

READ THROUGH THIS MANUAL BEFORE STARTING
CONSTRUCTION. IT CONTAINS IMPORTANT INSTRUCTIONS
AND WARNINGS CONCERNING THE ASSEMBLY AND
USE OF THIS MODEL.

GPMZ1542 for GPMA1542  V1.0

Entire Contents © Copyright 2006

Champaign, Illinois

(217) 398-8970, Ext 5

[email protected]

INSTRUCTION MANUAL

Wingspan: 41 in [1040mm] 
Wing Area: 356 sq in [23dm

2

Weight: 24 – 27 oz [680 – 765g]
Wing Loading: 9.7 – 10.9 oz/sq ft [30 – 33g/dm

2

Length: 38 in [960mm] 
Requires (not included):
Radio: 
4-channel with four micro servos, two 6" [152mm] servo

extensions and one Y-harness

Motor: RimFire

35-30-950 out-runner (GPMG4590) or

Ammo

24-33-4040 in-runner brushless motor (GPMG5165)

Gear-Drive: 24mm gear-drive with 4.5:1 gear ratio
ESC: 25 amp brushless ESC
Battery: 3-cell 1250 to 2100mAh LiPo battery & 

LiPo-compatible charger

Содержание Yak 54 36 ARF





























Отзывы: