GREAT PLAINS YP2425 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 166

background image

2016-11-16

Table of Contents

401-406M

YP2425 and YP2425F

Table of Contents

Adjustments

82

Seed Firmer Adjustments

Series 25 row units include a standard seed flap, and
accept one of two optional seed firmers (which may be
included in your selected opener bundle).

Sharp Object Hazard:
Row unit disk blades may be sharp. Use caution when making
adjustments in this area. To adjust the Keeton

®

Seed Firmer,

lower the planter until the disks of the row units are resting on
the ground.

Keeton Seed Firmer Adjustment

The optional Keeton

®

Seed Firmer is an engineered

polymer shape that slides down the seed trench. It traps
seeds as they exit the seed tube and firms them into the
bottom of the “V”.

Refer to Figure 115

The firmer is provided with a preset tension which is
recommended for using the first year. The tension
screw

can be tightened in subsequent years

according to your needs. Firmers should provide just
enough tension to push seeds to the bottom of the trench.

Seed-Lok

®

Seed Firmer Lock-Up

Optional Seed-Lok

®

firming wheels provide additional

seed-to-soil contact. The wheels are spring loaded and
do not require adjusting. In some wet and sticky
conditions the wheels may accumulate soil. To avoid
problems associated with this, you can lock-up the
firmers.

Refer to Figure 116 (which depicts a row unit with
discs, side depth wheels/arms and press wheels
removed for illustrative purposes - removal is not
necessary for lock/unlock)

To lock up Seed-Lok

®

wheels:

1.

Raise planter. Insert lift assist cylinder locks.

2.

Lift Seed-Lok

®

lock-up handle

until lever stop

is

free to rotate.

3.

Rotate lever stop to side/idle position

. Release

lock-up handle

.

4.

Push up on Seed-Lok

®

wheel

until wheel arm

latches up

.

To release a locked-up Seed-Lok

®

:

1.

Insert a

1

/

4

in tool drive tip in the tool hole

of the

handle

. Alternatively, lift up on the wheel

.

2.

Rotate the handle clockwise (handle arm up) until
the Seed-Lok

®

wheel releases at the latch point

and falls free.

3.

While holding the handle up, rotate the raised portion
of the lever stop

under both sides

of the handle

at the arm end. Remove the tool.

Figure 115

Keeton

®

Seed Firmer

20327

1

1

Note:

Engage the lever stop under the handle

when

Seed-Lok

®

is in use. If left disengaged

, a

furrow obstruction could cause unintended lock-
up.

Figure 116

Seed-Lok

®

Lock-Up

31543

2

3

1

4

2

3

5

6

1

2

3

1

4

5

6

1

4

5

2

2

«
...
84
85
86
87
88
...
»

Содержание YP2425







































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YP2425

SABO 43-COMPACT E

Бренд: Sabo Страницы: 116

Бренд: Sabre Страницы: 191

Бренд: Poulan Pro Страницы: 30

Бренд: Yazoo/Kees Страницы: 24

Cheetah SCZ48V-22FX

Бренд: Scag Power Equipment Страницы: 78

Бренд: Barbieri Страницы: 2

Patriot FDR1660

Бренд: Land Pride Страницы: 2

Throw Reel Mower

Бренд: Mclane Страницы: 16

Бренд: Peco Страницы: 12

Бренд: Lawn-Boy Страницы: 28

LX466 13AT61RH044

Бренд: Toro Страницы: 36

Бренд: TYM Страницы: 169

Бренд: Craftsman Страницы: 36

Бренд: Craftsman Страницы: 20

Бренд: Sealey Страницы: 4

Бренд: Husqvarna Страницы: 24

Бренд: Husqvarna Страницы: 36

Бренд: Husqvarna Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды