GREAT PLAINS YP2425 Скачать руководство пользователя страница 8

Страница: 8 / 166

2016-11-16

Table of Contents

Index

401-406M

YP2425 and YP2425F

Table of Contents

Index

Important Safety Information

Tire Safety

Tire changing can be dangerous and should be
performed by trained personnel using correct tools and
equipment.



When inflating tires, use a clip-on chuck and extension
hose long enough for you to stand to one side–not in front
of or over tire assembly. Use a safety cage if available.



When removing and installing wheels, use wheel-handling
equipment adequate for weight involved.

Practice Safe Maintenance



Understand procedure before doing work. Use proper
tools and equipment. Refer to this manual for additional
information.



Work in a clean, dry area.



Lower the planter, put tractor in park, turn off engine, and
remove key before performing maintenance.



Make sure all moving parts have stopped and all system
pressure is relieved.



Allow planter to cool completely.



Disconnect battery ground cable (-) before servicing or
adjusting electrical systems or before welding on planter.



Inspect all parts. Make sure parts are in good condition
and installed properly.



Remove buildup of grease, oil or debris.



Remove all tools and unused parts from planter before
operation.

Содержание YP2425







































































































































































Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды

GREAT PLAINS YP2425, Руководство оператора

Результаты поиска

Содержание YP2425

Отзывы:

Похожие инструкции для YP2425

Бренды по названию

Популярные бренды