GREAT PLAINS Yield-Pro YP4025A-48TR20 Скачать руководство пользователя страница 64

Страница: 64 / 190

2019-03-19

Table of Contents

Index

411-198M

YP4025A-48TR20

Table of Contents

Index

Operating Instructions

Implement Name Fertilizer Tanks (Option)
Filling Tanks

Refer to Figure 59, Figure 55 on page 54 and

Figure 56 on page 57

1. Connect nurse-tank hose to quick-fill coupler

located at the rear tool bar. Lock hose in place with

cam-lock levers.

2. Close valve

(not shown) going to the in-line filter

located just before the pump.

3. Open valves

at each tank and at quick-fill

coupler.

4. Fill tanks, then close valve at quick-fill coupler, and

disconnect the nurse tank hose.



Always close valve

at filter when filling or storing

any liquid in tanks. Failure to do so may allow material

to run out of manifold outlets causing contamination

from spillage.



Always fill fertilizer tanks to equal levels. If one tank

fills more quickly, shut that tank valve off to raise the

level in the other tank.

Implement Name Pump System Operation

Refer to Figure 55 on page 54

For normal field operations with fertilizer application,

after loading fertilizer, set the system valves as follows:
1.

rear quick-fill: closed

tank recirculation (2): open

pump main discharge selector: open to pump

and boom

tank discharge (2): open

pump bypass/recirculation: open briefly to

gravity-prime pump, then closed if desired for high

rate application

boom shut-off (strainer isolation) valve: open

Cart Pump System Operation

Refer to Figure 56 on page 57

For normal field operations, when applying fertilizer, set

the system valves as follows:
1.

cart quick-fill: closed

tank recirculation: open

pump main discharge selector: open to pump

and boom

cart hose valve: open

rear implement name inlet: open

tank discharge: open

pump bypass/recirculation: open briefly to

gravity-prime pump, then closed if desired for high

rate application

Figure 59

Quick-Fill Coupler

29287

L16

L14

Agricultural Chemical Hazards:

Avoid contact with skin or eyes. Wear proper protective
equipment as required by chemical manufacturer. Avoid

prolonged breathing of chemical fumes. Wear respirator as

required by chemical manufacturer. Some chemicals will cause
serious burns, lung damage and death. Seek medical

assistance immediately if accident occurs. Know what to do in

case of an accident.

Содержание Yield-Pro YP4025A-48TR20































































































































































































Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS Yield-Pro YP4025A-48TR20, Руководство оператора

Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Бренды по названию

Популярные бренды