GREAT PLAINS Yield-Pro YP4025A-48TR20 Скачать руководство пользователя страница 18

Страница: 18 / 190

2019-03-19

Table of Contents

Index

411-198M

YP4025A-48TR20

Table of Contents

Index

Introduction

Great Plains welcomes you to its growing family of new

product owners. The 40 Foot 3-Section Yield-Pro®

Planter (YP4025A-48TR20 implement name) has been

designed with care and built by skilled workers using

quality materials. Proper setup, maintenance, and safe

operating practices will help you get years of satisfactory

use from the machine.

Models Covered

Description of Unit

The YP4025A-48TR20 Product is a pull-type implement

with optional mounted or pull-behind fertilizer capability.

The YP4025A-48TR20 includes 25 Series openers with
Air-Pro

meters supporting a wide choice of seed disks.

The product accepts optional unit mounted and

frame-mounted row accessories. The product folds for

transport.

Intended Usage

Use the YP4025A-48TR20 Product to seed

production-agriculture crops only. It is suitable for

conventional till, min-till and moderate no-till conditions.

Do not modify the product for use with attachments other

than Great Plains options and accessories specified for

use with the YP4025A-48TR20.

Document Family

Other row spacings of model Product # are covered by

separate Operator and Material Rate manuals

(401-627M and 401-627B).

Using This Manual

This manual will familiarize you with safety, assembly,

operation, adjustments, troubleshooting, and

maintenance. Read this manual and follow the

recommendations to help ensure safe and efficient

operation.
The information in this manual is current at printing.

Some parts may change to assure top performance.

Definitions

The following terms are used throughout this manual.

A crucial point of information related to the preceding topic.

Read and follow the directions to remain safe, avoid serious

damage to equipment and ensure desired field results.



Useful information related to the preceding topic.

Right-hand and left-hand as used in

this manual are determined by facing

the direction the machine will travel

while in use unless otherwise stated.

An orientation rose in some line art

illustrations shows the directions of:

Up, Back, Left, Down, Front, Right.

YP4025A-48TR20

48-Twin Row, 20 inch (51 cm)

Figure 1

YP4025A-48TR20 Product

29817

ManualM #

Operator Manual (this document)

ManualB #

Seed and Fertilizer Rate Charts

ManualP #

Parts Manual

DICKEY-john

IntelliAg

manuals:

11001-1662

Planter/Drill Control, User Level 1

11001-1501A Planter/Drill Control, User Level 2&3
110011651

Quick Start Guide YP4025A-48TR20

11001-1126

DICKEY-john

hopper level sensor install

Содержание Yield-Pro YP4025A-48TR20































































































































































































Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS Yield-Pro YP4025A-48TR20, Руководство оператора

Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Бренды по названию

Популярные бренды