GREAT PLAINS Yield-Pro YP4025A-48TR20 Скачать руководство пользователя страница 145

Страница: 145 / 190

YP4025A-48TR20

Table of Contents

Index

Options

141

2019-03-19

Table of Contents

Index

411-198M

Fertilizer Orifice Plates

The manifold systems include size 28, 34 and 48 plates.

To order alternate plates, use the following part numbers.

Order one per row unit.

VeriFlow Nozzles

To eliminate the need to change orifice plates, you can

replace the standard Great Plains nozzles with

SprayTarget VeriFlow nozzles. These contain a

spring-loaded regulator that provides consistent

back-pressure over a wide range of rates and pressures.
Great Plains offers two models of VeriFlow nozzles:

Order one nozzle per active boom clamp.

High-Rate Dribblers



For use only with 25 Series openers.

Dribblers apply liquid fertilizer slightly to the side of the

closed furrow behind the press wheel. Dribblers are

available in left and right hand offsets, for use on twin

rows. Order one dribbler per row.

34976

Orifice

Part

Port

Size

Number

Diameter

Area

832-052C

0.020 in

0.20 mm²

28*

832-056C

0.028 in

0.40 mm²

34*

832-053C

0.034 in

0.59 mm²

48*

832-054C

0.048 in

1.17 mm²

59 832-057C

0.059

1.76 mm²

832-055C

0.080 in

3.24 mm²

832-059C

0.098 in

4.87 mm²

29993

* Sizes standard in many fertilizer bundles.

Check your accessories before ordering.

Description

Part Number

NOZZLE HI-VERIFLOW1

(0.25 to 2.8 gpm at 15 to 60 psi)

829-143C

NOZZLE VERIFLOW1

(0.15 to 1.5 gpm at 15 to 60 psi)

829-144C

36424

Option Packages

Part Number

Fertilizer Dribbler Assembly, RH

204-131A

Fertilizer Dribbler Assembly, LH

204-132A

27174

Содержание Yield-Pro YP4025A-48TR20































































































































































































Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Похожие инструкции для Yield-Pro YP4025A-48TR20

Бренды по названию

Популярные бренды

GREAT PLAINS Yield-Pro YP4025A-48TR20, Руководство оператора

Результаты поиска

Содержание Yield-Pro YP4025A-48TR20

Отзывы:

Похожие инструкции для Yield-Pro YP4025A-48TR20

Бренды по названию

Популярные бренды