manualshive.com logo in svg

GREAT PLAINS SS0300, Оригинальное руководство пользователя

Поделиться
Скачать
GREAT PLAINS SS0300 Скачать руководство пользователя страница 21

SS0300

Table of Contents

Index

Operating Instructions

Great Plains

 | 596-224M | 3/22/19

Table of Contents

Index

17

Transporting

See  “

Hitching  Tractor  to  Sub-Soiler

”  on  page 12

before transporting the product.

Check Tractor Capacity and Configuration

•

Consult your tractor manual for 3-point limitations.

•

Add weights to tractor as required.

When determining the weight of your product, be sure to

include the weight of any options.

Transport Checklist

Plan the route. Avoid steep hills. Keep Clearances in 

mind.

Make all electrical and hydraulic connections. See 

“

Hitching Tractor to Sub-Soiler

” on page 12.

Raise product.

Always have lights on for highway operation.

Comply with all federal, state and local safety laws 

when traveling on public roads. 

Travel with caution. Allow safe clearance.

Remember that the product is wider than the tractor.

Parking

Perform the following steps when parking the implement.

Refer  to  “Storage”,  page  19,  to  prepare  for  long-term

storage.
1. Park implement on a level, solid area.

2. Lower implement until shanks are resting on the 

ground.

Refer to Figure 13
1. Lower and pin parking stands. 

2. Unplug light harness lead from tractor receptacle. Do 

not allow lead to rest on the ground.

3. Unhitch from the tractor 3-point.

Loss of Control Hazard:

Use a tractor rated for the load. Add tractor ballast as needed.
Do not exceed 20 mph. Towing the product with a vehicle that is

not adequate, or at high speeds, could lead to loss of vehicle

control. Loss of vehicle can result in a serious road accident,
severe injury or death. Check that your tractor has enough to

handle the weight of the product. Refer to your tractor’s

operator manual for capacities and ballast requirements.

Null4:

Figure 13

Parking Stands

41935

Содержание SS0300



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды