GREAT PLAINS RC4015 Скачать руководство пользователя страница 20

Страница: 20 / 60

Section 1: Assembly & Set-up

RC4015 & RCM4015 Rotary Cutters 334-300M

9/19/16

Table of Contents

Transport Bar, Locked Position

Figure 1-17

Lower Wings

DANGER

Keep everyone out of the area where the wing decks will
unfold into. A wing that falls suddenly on a person will cause
serious bodily injury or death.

Refer to Figure 1-17:

Park tractor and cutter on a level surface.

Raise both wings up to release any tension on
transport lock bars (#3).

Shut tractor down properly before dismounting. Refer
to

“Tractor Shutdown Procedure”

on page 13.

Remove hairpin clip (#1) from both the left and right
cylinder pins (#4).

Refer to Figure 1-18:

Rotate end of transport lock bars (#3) to storage
pins (#2) on both left and right wings.

Secure with hairpin clips (#1).

Restart tractor and lower both left and right wings
with tractor hydraulic control lever until both wings
are on the ground.

27921

Transport Bar, Storage Position

Figure 1-18

Driveline Installation

DANGER

Do not engage tractor PTO while hooking-up and unhooking
driveline or while someone is standing near the driveline. A
person’s body and/or clothing can become entangled in the
driveline resulting in serious injury or death.

WARNING

Always disengage PTO, place tractor in park or set park
brake, shut tractor engine off, remove switch key, and wait for
blades to stop before dismounting from tractor.

WARNING

Do not operate cutter above its rated PTO speed or machine
breakage may result.

WARNING

Make certain all driveline yokes are securely fastened at both
ends. A loose yoke can work free allowing the driveline to
rotate uncontrollably causing machine damage and bodily
injury or death to anyone nearby.

27923

IMPORTANT:

Do not attempt to operate a 540 rpm

driveline at 1,000 rpm or a 1,000 rpm driveline at 540
rpm. Many tractors provide both 540 and 1,000 rpm
PTO modes. Check your tractor’s manual to
determine its capabilities.

Содержание RC4015





























































Результаты поиска

Содержание RC4015

Отзывы:

Похожие инструкции для RC4015

Бренды по названию

Популярные бренды

GREAT PLAINS RC4015, Руководство оператора

Результаты поиска

Содержание RC4015

Отзывы:

Похожие инструкции для RC4015

Бренды по названию

Популярные бренды