GREAT PLAINS 8323, Инструкция по сборке

Страница: 15 / 142

Product # Table of Contents Index Assembly
Great Plains | 560-484Q-ENG | 2021 - 02 - 09 Table of Contents Index 11
Install Wing Cylinder Mount
Refer to Figure 9

The wing cylinder mount assemblies will be installed
as shown below for all wings.
42. Attach cylinder mount plate to inside of tube weldment
of wing frame, with 1 x 9 Gr. 8 hex bolt and 1 top lock
nut. Tighten bolt down snug.
43. Slide adjustment bolt assembly through front side of
ball joint on wing frame, secure with 1 slotted nut and
3/16 x 1 1/2 roll pin . Attach clevis end of adjustment
bolt assembly to rear hole of cylinder mount plate
with 1 x 2 29/64 clevis pin , 1.5 x 1.0 x.075 machine
washer and 3/16 x 2 cotter pin.

See side to side leveling in “Operator’s Manual” for
proper adjustment of wing when machine is
completely assembled.
Install 8323 & 8328 Wings
Refer to Figure 10

Be sure and install the 1 x 6 1/4 hinge pins as
shown with roll pin in slot on front side of hinge.
44. Carefully align holes in wing frame LH with holes in
center frame. Secure with 1 1/4 x 6 1/4 hinge pins , 3/8 x
2 1/2 roll pins, 1 flat washer and 1 top lock nut.
45. Attach wing brace to the front of the wing frame LH
with 3/4 x 2 hex bolts , 3/4 lock washers and 3/4 hex
nuts.
46. Align holes in wheel arm L , secure with 1 1/4 x 6 pins
, 3/8 x 2 1/4 hex bolts and 3/8 top lock nuts.
47. Mount wing fold bracket to wing with 3/4 x 5 hex bolts
, 3/4 lock washers and 3/4 hex nuts, 5/8 x 3 1/32 x 5 1/2
u-bolts , 5/8 lock washers and 5/8 hex nuts.
48. Attach base end of 3.25 x 8 x 1.25 lift cylinder to front
hole of cylinder mount plate with 1 x 3 1/8 pin , 1.5
x 1.0 x.075 machine washer and 3/16 x 2 cotter pin.
Attach rod end of 3.25 x 8 x 1.25 cylinder to wheel
arm L with 1 x 3 1/8 pin , 1.5 x 1.0 x.075 machine
washer and 3/16 x 2 cotter pin.
49. Attach base end of 4 x 30 x 1.5 fold cylinder to hole
of center fold bracket with 1 x 3 1/8 pin , 1.5 x 1.0
x.075 machine washer and 3/16 x 2 cotter pin.
50. Do not attach rod end of fold cylinders until fold system
has been purged, See “ Purging Hydraulic System ” on
page 26
51. Repeat same procedure for right wing.
52. Tighten all bolts to specs, See “
Torque Values Chart
” on
page 29.
Install 8332 & 8336 Wings
Refer to Figure 11

Be sure and install the 1 x 6
1

4
hinge pins as shown with roll pin in slot on front side of hinge.
4
2
1
3
6
5
Figure 9
Wing Cylinder Mount
41919
1
2
3
4
5
3 1
6
1
9
6
4
3
2
5
12
13
10
11
12
7
8
Figure 10
8323 & 8328 Wing
41905
2
1
2
3 1
4
5
6
7
8
9
10
11 12
10
5 12
13
12
2