GREAT PLAINS 3S-3000-3210 Скачать руководство пользователя | Manualshive

Страница: 7 / 118

background image

3S-3000/F/HD/HDF

Table of Contents

Important Safety Information

3

2018-06-18

Table of Contents

195-441M

Transport Machinery Safely

Maximum transport speed for drill is 20 mph (32 kph).
Some rough terrains require a slower speed. Sudden
braking can cause a towed load to swerve and upset.



Do not exceed 20 mph (32 kph). Never travel at a speed
which does not allow adequate control of steering and
stopping. Reduce speed if towed load is not equipped with
brakes.



Comply with national, regional and local laws.



Follow your tractor manual recommendations for
maximum hitch loads. Insufficient weight on tractor
steering wheels will result in loss of control.



Carry reflectors or flags to mark drill in case of
breakdown on the road.



Keep clear of overhead power lines and other
obstructions when transporting. Refer to transport
dimensions under “

Specifications and Capacities

Check for Overhead Lines

drill markers contacting overhead electrical lines can
introduce lethal voltage levels on drill and tractor frames.
A person touching almost any metal part can complete
the circuit to ground, resulting in serious injury or death.
At higher voltages, electrocution can occur without direct
contact.



Avoid overhead lines during seed loading/unloading and
marker operations.

Wear Protective Equipment



Wear protective clothing and equipment.



Wear clothing and equipment appropriate for the job.
Avoid loose-fitting clothing.



Because prolonged exposure to loud noise can cause
hearing impairment or hearing loss, wear suitable
hearing protection such as earmuffs or earplugs.



Because operating equipment safely requires your full
attention, avoid wearing entertainment headphones while
operating machinery.

«
...
5
6
7
8
9
...
»

Содержание 3S-3000-3210























































































































Отзывы:

Нет отзывов

Похожие инструкции для 3S-3000-3210

Бренд: Alpego Страницы: 32

Бренд: Alpego Страницы: 36

Бренд: Castolin Eutectic Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды