GREAT PLAINS 3S-3000-3210 Скачать руководство пользователя | Manualshive

Страница: 100 / 118

background image

2018-06-18

Table of Contents

195-441M

3S-3000/F/HD/HDF

Table of Contents

Appendix A - Reference Information

96

Appendix A - Reference Information

Specifications and Capacities

Tire Inflation Chart

3S-3000-6006

3S-3000HD-6006

3S-3000-4875

3S-3000HD-4875

3S-3000-3610

3S-3000HD-3610

Row Count

60

48

36

Row Spacing

6 in (15.2 cm)

7.5 in (19.1 cm)

10 in (25.4 cm)

Main Seed Box Capacity

92.7 bushels (3267 liters)

Tractor Requirements

125 hp minimum

Weight, standard model

a

a. See page 28 for additional weight data.

12447 lbs (5646 kg)

12425 lbs (5636 kg)

12409 lbs (5629 kg)

Weight, standard fert model

13496 lbs (6123 kg)

13454 lbs (6102 kg)

13416 lbs (6085 kg)

Down-Force per Row

130-207 lbs

(59-94 kg)

135-280 lbs

(61-127 kg)

144-373 lbs

(65-169 kg)

Opener Travel

8in (20cm)

Hydraulic Circuits

3 circuits required, load-sensitive or closed-center 15 to 30 gpm at 2300 psi

Optional kits are available for two-circuit, and open center.

Hitch Load

3700 lbs (1678 kg) folded with seed loaded

Caution:

negative tongue weight when raised and unfolded

Transport Width

15 feet (4.6 meters)

Operating Width

30 feet (9.1 meters)

Swath

365 in

(9.271m)

362 in

(9.195m)

360 in

(9.144m)

Height

7 feet 4 inches (224 cm)

Length

27 feet 7 inches (8.4 meters)

Tire Sizes 3S-3000/F

Gauge Wheels: 9.5Lx15 6-ply Rib Implement rib implement 6-bolt rim

Transport: 11Lx15 12-ply Rib Implement rib implement 6-bolt rim

Tire Sizes 3S-3000HD/HDF

Gauge Wheels: 265/70B16.5 NHS Skid Steer

Transport: 395/55B16.5 NHS Skid Steer

Tire Inflation Chart

Tire Warranty Information

Wheel

Tire Size

Inflation

All tires are warranted by the original manufacturer of the tire. Tire
warranty information is found online at the manufacturer’s websites
listed below. For assistance or information, contact your nearest
Authorized Farm Tire Retailer.
Manufacturer

Website

Firestone

www.firestoneag.com

Goodyear

www.goodyearag.com

BKT

www.bkt-tires.com/en

Gleason

www.gleasonwheel.com

Titan

www.titan-intl.com

Gauge

Wheel

9.5Lx15 8-ply

Rib Implement

32 psi

221 kPa

Transport

11Lx15 12-ply

Rib Implement

52 psi

359 kPa

Gauge and

Transport

Wheel

265/70B16.5 NHS

Skid Steer

60 psi

413 kPa

«
...
98
99
100
101
102
...
»

Содержание 3S-3000-3210























































































































Отзывы:

Нет отзывов

Похожие инструкции для 3S-3000-3210

Бренд: WIA Страницы: 28

Бренд: OHTAKE Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды