GREAT PLAINS 3S-3000-3210 Скачать руководство пользователя страница 52

Страница: 52 / 118

2018-06-18

Table of Contents

Index

195-441M

3S-3000/F/HD/HDF

Table of Contents

Index

Adjustments

Frame Level

Refer to Figure 44

The 00 and 00HD Series openers are designed to
produce optimal results when the opener frames are
level with the ground. Operating with drill frame level is
also recommended, and this is set by hitch height (page
18).

If planting depth is not as desired on just one or two drill
sections, first check the setup items for “

Leveling the

drill

” on page 74. Then check and adjust the following

items:

•

opener sub-frame adjustment: all gauge wheel
trunnions in same frame pivot holes - see
“

Opener-Subframe Adjustment

” on page 52,

•

opener pivot height: all openers pivoting in same
hole at their mounts (possibly excepting rows in tire
tracks) - see page 55,

•

opener press wheel height: all row units set the
same - see page 58, and;

•

opener spring down-force: all row units set the same
(possibly excepting rows in tire tracks) - see page 55.

Refer to Figure 45

This photograph illustrates openers too high in front.
Increase hydraulic pressure and/or lengthen opener
springs.

Check sub-frame pivot in use at higher pressures.

Refer to Figure 46

This photograph illustrates openers too low in front, also
known as “bulldozing”. Decrease hydraulic pressure
and/or shorten opener springs.

Check sub-frame pivot if pressures have recently been
reduced.

Figure 44

Frame & Openers Level

29131

Figure 45

Openers Too High in Front

29132

Figure 46

Openers Too Low in Front

29133

Содержание 3S-3000-3210























































































































Результаты поиска

Содержание 3S-3000-3210

Отзывы:

Похожие инструкции для 3S-3000-3210

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-3000-3210, Руководство оператора

Результаты поиска

Содержание 3S-3000-3210

Отзывы:

Похожие инструкции для 3S-3000-3210

Бренды по названию

Популярные бренды