GREAT PLAINS 3S-3000-3210 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 118

background image

2018-06-18

Table of Contents

195-441M

3S-3000/F/HD/HDF

Table of Contents

Adjustments

52

Opener-Subframe Adjustment

Refer to Figure 49

Each drill section has an opener frame which pivots
about the centerline of the drill gauge wheels. These
floating opener frames have the ability to rock the
openers 15 degrees up and 15 degrees down as a
group. By pivoting at the gauge wheels, openers
maintain a consistent depth as opener frames rock up
and back.

Down pressure for each opener frame is provided by two
cylinders working on a constant lever arm. When
combined with live hydraulics, the cylinders provide
constant down pressure across the width of each opener
frame – regardless of how the frame is positioned. Two
cylinders per opener frame along with special
trunnions

also provide some ability for one end of an

opener frame to rock independent of the other while
maintaining constant opener down pressure across the
frame.

At higher down-pressures (above 1800 psi) the row units
can tend to tip forward. An adjustment to the
mainframe/subframe pivot corrects this.The opener
frame has one adjustment point

for two different

operating positions.

Refer to Figure 50 (shown at factory setting)

You can adjust opener frames between two operating
positions–one for normal down pressure and one for
higher down pressure. The adjustment is near the
opener frame pivots. There are three holes and two
bolts. The bottom bolt

serves as the pivot. The top bolt

is for adjustment.

•

For normal drilling conditions, keep top bolt in
second (middle) hole

at all six frame pivots. Use

this setting when drilling with opener down pressure
below 1800 psi.

•

When drilling with opener down pressure above
1800 psi, place top bolt in top hole

on all six pivot

points across drill.

To change the bolts (to high pressure):

1.

Have a jack at hand.

2.

Loosen the nuts on all the top bolts

.

3.

Lower the opener sub-frames.

4.

Put the tractor hydraulic circuit for the openers in
float.

5.

Place jack under an opener tool bar at an arm.

6.

Lift the tool bar until the bolt is free.

7.

Remove the bolt.

8.

Repeat step 5 through step 7 the other arm of the
subframe.

9.

Raise the jack until the top holes are aligned.

10. Insert the bolt in the top hole

and spin on a nut.

11. Repeat step 5 through step 10 for each sub-frame.

12. Tighten all nuts.

Changing from high to low is similar, except lower the
jack at step 6 and reverse the bolt movement.

Figure 49

Opener-Frame Pivot

18857

1

2

Figure 50

Opener-Frame Adjustment

15558

3

4

5

«
...
54
55
56
57
58
...
»

Содержание 3S-3000-3210























































































































Отзывы:

Нет отзывов

Похожие инструкции для 3S-3000-3210

Streamfeeder Value Series

Бренд: Barry-Wehmiller Страницы: 58

Бренд: BLEC Страницы: 38

Бренд: Tar River Страницы: 38

Бренд: Tar River Страницы: 39

Бренд: ims PRO Страницы: 31

Бренд: Chapin Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды