GREAT PLAINS 3S-3000-3210 Скачать руководство пользователя страница 35

Страница: 35 / 118

3S-3000/F/HD/HDF

Table of Contents

Index

Operating Instructions

2018-06-18

Table of Contents

Index

195-441M

Unfolding

Drill must be lowered from transport lift prior to unfolding.
See “

Lowering Drill (Transport Lift)

” on page 30.

Verify that the site has clearance needed to unfold
drill.

If markers are installed, set Marker/Fold valve at
hitch to Fold.

Refer to Figure 23

Verify that the opener sub-frames are still raised and
locked up (handles in ROAD position).

Slowly supply oil to base end of fold circuit. Unfold
wing frames by completely extending fold cylinders.

If field operations are planned:

Position all six opener transport lock handles in
FIELD position.

Completely raise openers to allow opener transport
locks to disengage.



NOTE:

The opener transport lock handles are spring loaded
and can be moved to field position with openers up or
down, but locks will only disengage when openers are
completely raised. There are two lock handles on
each drill section.

Folding and Unfolding Quick Reference

To Fold Drill for Transport

•

Fold markers (page 41).

•

Raise openers (page 24).

•

Fold drill (page 25).

•

Raise drill (page 26).

To Unfold Drill for Field

•

Lower drill (page 31).

•

Unfold drill (page 31).

•

Set openers for FIELD (page 24).

Figure 23 - Unfold

Opener Unlock

15549

Содержание 3S-3000-3210























































































































Результаты поиска

Содержание 3S-3000-3210

Отзывы:

Похожие инструкции для 3S-3000-3210

Бренды по названию

Популярные бренды

GREAT PLAINS 3S-3000-3210, Руководство оператора

Результаты поиска

Содержание 3S-3000-3210

Отзывы:

Похожие инструкции для 3S-3000-3210

Бренды по названию

Популярные бренды