GREAT PLAINS 2S-2600 Скачать руководство пользователя страница 43

Страница: 43 / 114

2S-2600/F/HD/HDF

Table of Contents

Index

Operating Instructions

Great Plains

| 195-440M | 2019-05-03

Table of Contents

Index

Initial Seeding Depth

Refer to Figure 36

7. Set opener seeding depth by adjusting press-wheel

height . To adjust, first raise openers slightly, then

lift and slide T handles on top of openers Adjust all

press wheels to the same height. T handles adjust at



in (6.4mm) seeding depth change per minimum

handle step.
• For more shallow seeding, slide T handles forward

toward implement.

• For deeper seeding, slide T handles backward

away from implement.

8. While seeding, remember:

• Raise openers before turning. Never back up or

turn sharply with openers in the ground. Doing so

will plug openers and may damage equipment.

• Check periodically for plugged openers and

hoses.

For information on opener adjustments, see “

00 Row

Unit Adjustments

” on page 56. For information on

troubleshooting opener problems, see

“

Troubleshooting

” on page 66.

Figure 36

Initial Opener Depth

26441

Содержание 2S-2600



















































































































Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды

GREAT PLAINS 2S-2600, Руководство оператора

Результаты поиска

Содержание 2S-2600

Отзывы:

Похожие инструкции для 2S-2600

Бренды по названию

Популярные бренды