GREAT PLAINS 1510P Скачать руководство пользователя страница 37

Страница: 37 / 146

1510P & 1520P

Table of Contents

Index

Adjustments

Great Plains

| 118-732M | 4/4/19

Table of Contents

Index

Shutting Off Seed Flow

Refer to Figure 31

Figure 31 shows the sliding seed tubes in the open
position. To shut off seed flow, move front tubes
backward and back tubes forward. The following
instructions explain how to shut off seed flow to each
meter.

Refer to Figure 32

Remove the retaining clip and pull pin. Do not
remove cotter pin.

Refer to Figure 33

Move meter cap to position seed tube over shut off
pad.

Place pin in hole of meter cap and install retaining
clip.

Repeat steps 1 through 3 for each meter.



NOTE: When pin with retaining clip is located in the

slot, sliding seed tube is open. When pin with

retaining clip is located in the hole, sliding seed tube

is closed.

Figure 31

Sliding Seed Tubes in open positions

18290

Shut Off

Sliding Seed
Tubes

Figure 32

Removing Clip

18302

Retaining

Clip

Shut Off
Pad

Sliding Seed
Tube

18303

Figure 33

Replacing Pin

Содержание 1510P



















































































































































Результаты поиска

Содержание 1510P

Отзывы:

Бренды по названию

Популярные бренды

GREAT PLAINS 1510P, Руководство оператора

Результаты поиска

Содержание 1510P

Отзывы:

Бренды по названию

Популярные бренды