manualshive.com logo in svg

GREAT PLAINS 1510HDP, Руководство оператора

Поделиться
Скачать
GREAT PLAINS 1510HDP Скачать руководство пользователя страница 67

1525P and 1510HDP

Table of Contents

Index

Adjustments

Great Plains

 | 118-949M | 2018-07-03

Table of Contents

Index

63

Changing Seed Meter Wheel

Choose the correct seed meter wheel for the type of
seed you will be using. Be sure to use the same wheel
type on all meters.

Seed meter wheels for the interchangeable meter 25 series
opener are made of a green color material and are not
interchangeable with the other Great Plains seed meter wheels
for other machines. Use only green wheels in interchangeable
meter 25 series openers.

1.

Shut off seed flow to meters by moving sliding seed
tube. For more information see, "Shutting Off Seed
Flow," page 35.

2.

Clean out meter. For more information see "Cleaning
Out Meters," page 36.

Refer to Figure 83  

3.

Push in spring-loaded wheel retainer

 and turn.

Pull off wheel retainer and spring. 

Refer to Figure 84

4.

Pry the seed meter wheel out about a 

1

4

 inch using

tool stored under walkboard and spin backward to
clean out seeds from top pockets.

5.

Remove seed meter wheel.

With the seed meter wheel removed, you may want to
check the meter for internal damage or trash.Some
wear on top edge of slide is normal. Excess wear is
cause for replacement.

Refer to Figure 85

6.

Place new wheel on meter wheel shaft and push
meter slide retaining clip forward while pushing in
seed meter wheel.

Figure 83

Wheel Retainer

22872

1

Figure 84

Pry Seed Meter Wheel Out

22873

2

1

Figure 85

Place New Wheel on Shaft

22874

3

Содержание 1510HDP








































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды