Great Lakes VRX Highlander Скачать руководство пользователя страница 13

POWER AND GROUNDING OF ALL RACKS

When using PDUs, each PDU should be connected to a committed branch circuit that is rated 
for the continuous load of all the equipment connected.  When not using a PDU, each piece of 
equipment should be connected to a dedicated branch circuit.

PROTECTIVE EARTHING/GROUNDING

A main protective earthing stud is provided.

 

WARNING:

 

To avoid injury to persons or loss of life, ground rack individually to the dedicated branch circuit 

earthing ground.

CONNECTING MAIN PROTECTIVE EARTHING STUD TO THE DEDICATED BRANCH CIRCUIT 

EARTHING GROUND CONDUCTOR

Connect the dedicated branch circuit earthing ground conductor to the main protective earthing 
stud located on the support frame using a listed ring or closed-loop terminal.

PARTS NOT BONDED TO PROTECTIVE EARTHING TERMINAL

The following parts are not effectively bonded to the protective earthing terminal: Top Cable 
Waterfall. If these parts need to be bonded to the protective earthing terminal, do so in accordance 
with Article 250 of the National Electric Code.

Although equipment may physically fit into a Great Lakes rack, with or without brackets, 
customers must also review and comply with the equipment manufacturer’s installation and 
other requirements.  For more information, please contact your Great Lakes representative or call 
1-866-TRY-GLCC.

When any equipment or accessory is installed in a Great Lakes product, the installation procedures, 
recommendations and product warranty requirements of the equipment manufacturer must be 
followed.  Great Lakes will not be responsible for any losses or claims arising from a customer’s 
installation of electrical, electronic or other third party products in any Great Lakes racks, unless 
caused solely by a written configuration prepared by Great Lakes for that customer or by a 
configuration provided by Great Lakes’ website, any configuration relies on complete and accurate 

information from the customer.

Product specifications are subject to change without prior notice.

13

Содержание VRX Highlander

















Отзывы: