Gravely Pro-Stance 99410000-1948FL Скачать руководство пользователя страница 26

Страница: 26 / 44

GB - 26

Installing Mower Deck Shield:

1. Insert rear of shield (B) under tabs on frame and lower shield

into position.

2. Secure with knobs (A).

Removing and Installing Mower Deck
Drive Belt Shields

Removing Belt Shields:

1. Park machine safely. (See Parking Safely in the SAFETY

section.)

MX20117

2. Remove belt shield locking knobs (A).
3. Remove belt shields (B) by sliding shield from mower deck

stud.

Installing Belt Shields:

1. Install belt shields (B) by sliding shield over mower deck stud.
2. Install belt shield locking knobs (A).

Adjusting Drive Belt Tension

1. Park machine safely.
2. Adjust mower deck to the 76 mm (3 in.) cutting height position.
3. Remove mower deck shield.

MX20118

4. Measure length (C) of tension spring from inside of hook to

inside of hook. The spring should measure 21.6 to 22.6 cm
(8-1/2 in. to 8-7/8 in.).

• To add tension to spring: Loosen jam nut (B). Turn nut (A)

clockwise. Tighten jam nut (B).

• To release tension from spring: Loosen jam nut (B). Turn nut

(A) counterclockwise. Tighten jam nut (B).

Replacing Mower Deck Drive Belt

Removing Mower Deck Drive Belt:

1. Park machine safely. (See Parking Safely in the SAFETY

section.)

2. Lower mower deck to the lowest cutting height position.
3. Remove mower deck shield.
4. Remove both mower deck belt shields.

MX20118

5. Release mower deck drive belt tension by turning adjuster nut

(A) counterclockwise until two threads remain protruding
through adjuster nut (A).

6. Disconnect idler spring (B) from idler arm (C) using a spring

puller tool.

MX20120

7. Loosen idler pulley retaining nut (D) just enough to allow idler

pulley (E) to tilt, allowing belt (F) to clear fixed belt guide (G).

8. Remove mower deck drive belt (F).

CAUTION: Avoid injury! Help prevent serious personal
injury. Do not operate the mower without the belt shields
installed.

CAUTION: Avoid injury! Tensioning spring is under high
tension. Wear gloves and safety glasses, and use a
spring puller to install and remove spring.

Содержание Pro-Stance 99410000-1948FL













































Результаты поиска

Содержание Pro-Stance 99410000-1948FL

Отзывы:

Бренды по названию

Популярные бренды

Gravely Pro-Stance 99410000-1948FL, Руководство владельца/оператора

Результаты поиска

Содержание Pro-Stance 99410000-1948FL

Отзывы:

Бренды по названию

Популярные бренды