Gravely 988105 Скачать руководство пользователя страница 24

Страница: 24 / 33

GB - 24

REMOVE SINGLE LEVER PLATE (988105,
106, 107, 108, 109, 113)

Without the single lever plate, the speed control levers
can work separately to adjust tracking on uneven
terrain.

To remove:

1. Remove knobs from speed control levers.

2. Remove and keep single lever plate.

3. Remove and keep nuts.

4. Apply Loc-Tite 495 (or equivalent) to knob

threads.

5. Replace knobs on speed control levers.

REPLACING THE HYDRO PUMP BELT

1. Place speed control levers in neutral position

(988105, 106, 107, 108, 109, 113).

2. Remove mower belt from mower clutch sheave

(Figure 19).

3. Remove pump belt idler spring from eye bolt.

4. Remove belt from engine sheave and pump

pulleys.

5. Install new belt on engine sheave and pumps.

6. Reconnect idler spring to idler.

7. Put mower belt back on mower clutch sheave.

CLUTCH ADJUSTMENT

If clutch fails to engage or disengage properly or
begins to make abnormal noise, check the air gap
adjustment at the three inspection slots.

To check:

1. Stop engine, remove key and wait for all hot parts

to cool.

2. Measure the air gap between the armature and

the rotor.

Minimum: A .005" feeler gauge should slide
between armature and rotor with slight contact.

Maximum: A .023" feeler gauge should slide
between armature and rotor with slight contact.

3. Repeat for each inspection slot.

To adjust:

1. If necessary, loosen gap adjustment nuts until a

.005" feeler gauge ﬁts between armature and
rotor.

2. Slide a .012" feeler gauge between armature and

rotor.

3. Tighten gap adjustment nut until there is slight

contact on feeler gauge.

4. Repeat steps 1 – 3 at each inspection slot.

NOTE:

Adjust air gap as evenly as possible.

5. Start unit, engage and disengage PTO.

6. Shut off unit.

7. Recheck air gap and adjust if needed.

WARNING:

An extension spring, when

extended, stores energy and can be
dangerous. Always use tools speciﬁcally
designed for installing or removing an
extension spring. Always compress or
extend springs slowly.

Figure 18

1. Neutral Bracket
2. Clevis
3. Speed Control Arm

Connect clevis
here for faster
speed range.

Figure 19

OG0795

1. Mower Clutch

Sheave

2. Mower Belt
3. Pump Belt Idler

Spring

4. Hydro Pump Belt
5. Pump Pulleys

Содержание 988105


































Результаты поиска

Содержание 988105

Отзывы:

Бренды по названию

Популярные бренды

Gravely 988105, Руководство владельца/оператора

Результаты поиска

Содержание 988105

Отзывы:

Бренды по названию

Популярные бренды