Gravely 785023 Скачать руководство пользователя страница 18

Страница: 18 / 30

CHAIN ADJUSTMENT

To adjust the power brush drive chain:

IMPORTANT: Adjust the chain after the first four hours of
operation and thereafter adjust every 100 operating
hours.

1. Loosen the nut and move the block against the

chain until the chain is straight at the top. DO NOT
OVERTIGHTEN the chain. Tighten the nut. See
figure 22.

BRUSH REPLACEMENT

To replace the brush element:

1. Disconnect the brush from the unit.

2. Turn the power brush over with the wheels up.

3. Remove the side plate.

4. Remove the connecting link from the chain.

Remove the chain from the sprocket. See figure 23.

5. Remove the bolts from the flangette bearing on

each end of the brush. See figure 24.

6. Remove the brush from the support frame.

7. Loosen the locking collar set screw. Put a punch in

the hole without threads. Hit the punch with a
hammer to turn the locking collar 1/4 turn
counterclockwise.

8. Remove the locking collar and the bearing from the

shaft.

9. Remove the .25 x 2.00 cotter pin and the three

spacers from the shaft. See figure 24.

10. Remove the shaft from the brush.

11. Install the replacement brush on the shaft. Put the

spacers on the shaft and install the .25 x 2.00 cotter
pin.

12. Put the flangette bearing on the shaft with the flat

side toward the brush. Put the locking collar on the
bearing shoulder. DO NOT TIGHTEN THE
LOCKING COLLAR AT THIS TIME.

13. Put the brush in the frame.

14. Fasten the sprocket side flangette bearing to the

support frame first, using the hardware removed in
Step 5.

15. Fasten the opposite flangette bearing to the frame

on the other side.

16. To tighten the locking collar, put a punch in the hole

without the threads. Hit the punch with a hammer,
turning the locking collar clockwise until tight.

17. Put the chain on the sprocket and install the

connecting link and retainer clip.

18. Adjust the chain for tension per the Chain

Tightening instructions.

19. Install the left side plate on the frame using

the.31-18 x.75 hex bolts and nuts.

Figure 22

Nut

Chain

Block

Figure 23

Connecting Link

Chain

Connecting

Link Retainer

Figure 24

Brush

Element

Flangette

Bearing

Cotter

Brush

Shaft

Locking

Collar

Shaft

Spacers

Flangette

Nut

Flangett

Bolt

Set

Screw

Brush

Frame

Содержание 785023































Результаты поиска

Содержание 785023

Отзывы:

Похожие инструкции для 785023

Бренды по названию

Популярные бренды

Gravely 785023, Руководство оператора и каталог запасных частей

Результаты поиска

Содержание 785023

Отзывы:

Похожие инструкции для 785023

Бренды по названию

Популярные бренды