background image

www.modellmarkt24.ch;   www.modellmarkt24.de

10 / 16

S1031_HB_V1

Range test

Switch the 

mz-4

 

HoTT 

transmitter and your receiver on. Hold the 

"CUT OFF/ BIND" (5) button pushed for about 5 sec The range 
test is active for 90 seconds. At the begin the LED 2 will light up 
twice red with two signal tones. Walk about 10 m away from the 
model and move the control stick to the left and to the right. A 
second person, which remains by the model, should verify the 
control movements on the model. If the control movements are 
not received by the model within 10 m, check the power supply 
in the model and in the transmitter.

Interruption of the range test is always possible by pushing on 
the CUT OFF/BIND button (5). Confirm through a signal tone, 
LED 2 lights on red again.

Motor CUT OFF/Motor ON

This function switches the motor on and off. Thus avoids an 
accidental start of the motor.

1.  Move the throttle stick to the lowest position

2.  Push on the CUT OFF/BIND button (5) for about 2 s. The 

yellow LED (1) light off

3.  The motor is now activated.

Pushing the control stick forward the motor will start.

Push on the CUT OFF/BIND button again, the yellow LED (1) 
lights on again and the motor is deactivated.

Change model

The 

mz-4

 

HoTT

 has 10 model memories. These model memories 

are pre-set for the Vector Planes.

The last number of the Vector Planes order number indicates 
the model memory number.

For example: No. 13301 LEO indicates the model memory 1

The model change works only if the motor is deactivates (motor 
CUT OFF), which means the yellow LED (1) must be lighting.

1.  Push the control stick switch for about 5 sec.

2.  A 2x single signal tone follows.

3.  Release the control stick switch.

The LED (1) indicates the actual model memory, e.g. for model 
memory 4 the LED will blink 4 times before having a 3 sec. 
pause

The model memory can be changed through the trim buttons 
(3) - or (4) +

Push the control stick switch for about 2 sec. a 2 single signal 
tone is emitted to confirm the model change.

2

CUT OFF/BIND

1

www.modellmarkt24.ch;   www.modellmarkt24.de

Содержание mz-4

















Отзывы: