background image

05

    

 

 

 

 

      33700 SMART-BOX - Graupner HoTT 2.4

    

Transmitter low-voltage warning (ALARM VOLT): 

you can adjust the low voltage threshold at which the 

alarm (continuous beeping) is triggered; the available range is 4 - 15 V.
When the alarm is triggered, “VOLT-E” 

fl

 ashes at top right in the SMART-BOX transmitter display, and the 

parameters ACTION VOLT and ALARM VOLT are displayed in inverse form.

Note: 

the transmitter has an integral low-voltage warning (beep) which is triggered when the transmitter 

voltage falls to 9.4 V, regardless of the value set using the SMART-BOX.

Country selection (COUNTRY):

 The Country setting is present in order to cater for various directives (FCC, 

ETSI, IC etc.). The HoTT 2.4 radio system features a restricted frequency band for France. If you wish to use 
the RC system in France, the country setting on the transmitter must be set to “France” mode, as described. 
It is essential not to use the Universal/EUROPE mode. Factory setting is GENERAL.

Range checking (RANGE TEST):

 

switches the range test on or off, the remaining time is displayed. The display also works if the range check 
is started with the BIND / RANGE button on the transmitter.

Multichannel 1 / 2 (MULTIC 1 / 2:

 Multi-channel function for the use with the Nautic-Expert-Module order 

no. 4108. Up to 2 multi-channel channels can be used, the appropriate channels must be set in the display 
under MultiC. If no Nautic module is used, set MULTIC to 00.

Note:

 only suitable for digital servos! The cycle time (PERIOD) must be set to 10 msec, the channel se-

quence (CH OUTPUT TYPE) to SAME so that the function is activated!

3.2. RECEIVER DISPLAY

3.2.1 Receiver Data View (RX DATAVIEW)

If you wish to switch to the receiver data display, press the ENTER button repeatedly until RX DATAVIEW 

appears on the screen.
Please note: menus 3.2.1 to 3.2.6 can only be selected when the receiver 
is switched on. When you switch the receiver on, it may take a few se-
conds before the receiver display becomes active and can be selected: > 
symbol appears at the top right corner of the transmitter display (TX).
There may be a slight delay in the screen’s response to inputs using the 
top buttons, since all the settings are transmitted directly to the receiver 
by wireless means.

In the receiver data view display settings can not be made.

 RX DATAVIEW                   >      

S-QUA 100% S-dBm -49dBm   

S-STR  065% R-TEM. +30°C

L PACK TIME      00005msec

R-VOLT : 

05.9V

LR-VOLT : 05.8V

SENSOR1 : 00.0V   

00°C

SENSOR2 : 00.0V   

00°C

Display

Description

Setup

S-QUA

Signal quality in %

-

S-dBm

Receive performance in dBm

-

S-STR

Signal strenght in %

-

R-TEM

Receiver temperature in °C

-

L PACK TIME

indicates the duration of signal loss of the longest data packet du-

ring transmission from transmitter to receiver; stated in msec

-

R-VOLT

Actual receiver operating voltage in Volt

-

L.R-VOLT

Minimum receiver operating voltage since it was last switched on; 

stated in Volt

-

Sensor 1

the values of the optional telemetry sensor 1 in Volt and °C

-

Sensor 2

the values of the optional telemetry sensor 2 in Volt and °C

-

Содержание HoTT SMART-BOX

























Отзывы: