GRASS VALLEY K2 SAN Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 346

background image

For media (iSCSI) network interface

Setting...

Disabled, since names are excluded from the hosts file. Disregard.

Set to Default

Disabled, since names are excluded from the hosts file. Disregard.

...use Interface
Name/Aliases in
Host Files...

Disabled, since names are excluded from the hosts file. Disregard.

Aliases

Disabled, since names are excluded from the hosts file. Disregard.

DNS Suffix

4. Click

OK

to save settings and close.

About SiteConfig support on K2 devices

Before SiteConfig can be used to discover or manage a device, the device must meet the following
requirements:

•

The device must be a Microsoft Windows operating system device.

•

The device must have Microsoft .NET version 3.5 installed, as reported in the Windows
Add/Remove Programs control panel.

•

The SiteConfig Discovery Agent service must be running on the device, as reported in the
Windows Services control panel.

For K2 clients and K2 Media Servers shipped new from Grass Valley with K2 software version 7.0
or higher, these requirements are pre-installed. These requirements are pre-installed on recovery
images for these K2 systems as well. Therefore, if you suspect a problem with these requirements,
do not attempt to install SiteConfig support requirements. If you must restore SiteConfig support
requirements, re-image the K2 system.

Discovering devices with SiteConfig

Prerequisites for this task are as follows:

•

The Ethernet switch or switches that support the control network are configured and operational.
If multiple switches, ISLs are connected and trunks configured.

•

The PC that hosts SiteConfig is communicating on the control network.

•

There are no routers between the PC that hosts SiteConfig and the devices to be discovered.

•

Devices to be discovered are Windows operating system devices, with SiteConfig support
installed.

•

Devices are cabled for control network connections.

•

If discovering a device with Microsoft Windows Server 2008 operating system, the device must
have an IP address, either static or DHCP supplied.

1. Open SiteConfig.

2014 01 27

K2 SAN Installation and Service Manual

85

Planning and implementing a K2 SAN with SiteConfig

«
...
83
84
85
86
87
...
»

Содержание K2 SAN



























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K2 SAN

Бренд: WiebeTech Страницы: 4

Бренд: kincrome Страницы: 3

Бренд: ManoMano Страницы: 8

Бренд: Ykk ap Страницы: 36

Бренд: DuraMax Страницы: 81

Бренд: AIC Страницы: 101

Бренд: IBM Страницы: 104

Бренд: Seagate Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 52

Бренд: Facom Страницы: 2

Garage Workshop T3

Бренд: Stanley Страницы: 16

actiLib Autoloader 2U

Бренд: Actidata Страницы: 84

Бренд: ABSCO SHEDS Страницы: 25

Бренд: Advantech Страницы: 110

Бренд: LapSafe Страницы: 7

WD1500AHFD - Raptor X 150 GB Hard Drive

Бренд: Western Digital Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды