GRASS VALLEY K2 BASECAMP EXPRESS Скачать руководство пользователя страница 305

Страница: 305 / 366

4. In the K2 System Configuration application, open the Network configuration page for the K2

client.

5. Verify that the IP address updates correctly.

6. If a K2 Summit system, enable the write filter. You can do this in K2Config or in K2Config.

7. Restart the K2 client.

on page 305

Enabling and disabling the write filter using K2Config

on page 305

Enabling and disabling the write filter using K2Config

Before doing this task, make sure that your K2 Summit system is in a state as follows:

•

Media access is stopped

•

The K2 Summit system is not being used

This task required a restart.

You can use the K2Config application to enable and disable the writer filter on a SAN-attached K2
Summit system.

1. On the PC that hosts K2Config, open the K2Config application.

A login dialog box opens.

2. Log in to the K2Config application with the administrator account.

The K2Config application opens.

02 February 2012

K2 SAN Installation and Service Manual

305

Administering and maintaining the K2 SAN

Содержание K2 BASECAMP EXPRESS















































































































































































































































































































































































Результаты поиска

Содержание K2 BASECAMP EXPRESS

Отзывы:

Похожие инструкции для K2 BASECAMP EXPRESS

Бренды по названию

Популярные бренды

GRASS VALLEY K2 BASECAMP EXPRESS, Инструкция по установке и обслуживанию

Результаты поиска

Содержание K2 BASECAMP EXPRESS

Отзывы:

Похожие инструкции для K2 BASECAMP EXPRESS

Бренды по названию

Популярные бренды