GRASS VALLEY IQUCP25 Скачать руководство пользователя страница 249

Страница: 249 / 338

249

Getting Started with the Multiviewer

Multiviewer SDC Overview

Architecture

The Multiviewer SDC comprises two software interfaces that are individually configured:

• the Multiviewer SDC software
• that runs on top of the UCP

3901 Card’s input/output hardware.UCP

3901 Card

Video IP streams are transmitted from or received at ‘spigots’ and may be sent/received on

redundant networks. Destination spigots receive IP streams (IP Rx) and source spigots send

IP Streams (IP Tx). The UCP

3901 Card has the following functional inputs and outputs:

• 12 × destination spigots for the Multiviewer video IP stream inputs (IP Rx).
• Multiviewer head outputs:

• 4 × source spigots for mosaic IP stream outputs (IP Tx).
• 4 × mosaic SDI video HD-BNC copy outputs available on the rear panel. See

12G/3G/HD/SD-SDI I/O – Serial digital video inputs / outputs (4)

, on page 34 and

3G / HD / SD SDI I/O – Serial digital video inputs / outputs (12)

, on page 35.

Multiviewer Input Scaling

There are 12 image scaling blocks within the multiviewer. This means that:

• There is only one scaling block per input.
• An input can only appear one time on any head display output.

Grass Valley Orbit

The Grass Valley Orbit software tool is used to configure Grass Valley products. RollCall

templates may be viewed and used through Orbit.

UCP‐3901 Card

Multiviewer

SDC

Video IP

Streams: IP Rx

Mosaic IP
Streams: IP Tx

SDI, HD‐BNC

Video Inputs

12 ×

Destination

Spigots

4 × Source

Spigots

Head Display

Outputs

Содержание IQUCP25



















































































































































































































































































































































Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды

GRASS VALLEY IQUCP25, Руководство пользователя

Результаты поиска

Содержание IQUCP25

Отзывы:

Похожие инструкции для IQUCP25

Бренды по названию

Популярные бренды