GRASS VALLEY 8910ADA-M - Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 58

background image

14

8910ADA-M/ST/SR — Instruction Manual

Installation

Rear Module Installation

To install a rear module into GeckoFlex frame, follow these steps:

Note

Module Installation Precautions

before installing the

rear module.

1.

Each 8900A-R rear module or blank rear adapter cover is held in place
by two retainer clips as shown in

. Loosen (but do not remove

completely) the two screws holding each retainer clip to the frame with
a 2 mm (5/64”) hex screwdriver. Pull up on the retainer to remove it,
leaving the screws in place.

CAUTION

Be careful to leave the screws in place as they can be easily lost or fall into
equipment below the frame creating a shorting hazard.

2.

Remove the blank rear adapter cover by inserting needlenose pliers
into the slots in the top and bottom of the blank and pulling it off.

Note

To remove a rear module already installed, follow the same steps. It is helpful
to first remove the front module so the rear can be pulled out more easily.

3.

Insert the rear module into the empty slot.

4.

Replace each retainer clip over the two screws on both sides of the
module and push down to seat the retainer.

5.

Tighten the screws for each retainer clip just until they are snug. Do not
force or torque the screws too tightly. The rear retainer clip screw torque
specification is 4-5-inch-lb./0.45-0.60Nm.

Figure 3. Installing Rear Module

Use needlenose pliers
to pull out blank after
removing retainers.

«
...
12
13
14
15
16
...
»

Содержание 8910ADA-M -



























































Отзывы:

Нет отзывов

Похожие инструкции для 8910ADA-M -

Бренд: Nakamichi Страницы: 34

Rampage AXTM-600

Бренд: Audiovox Страницы: 12

SINGLE RECTIFIER RECT-O-VERB 50 2 Series

Бренд: Mesa/Boogie Страницы: 11

Valvestate VS230R

Бренд: Marshall Amplification Страницы: 7

Бренд: LD Страницы: 28

Бренд: HR Страницы: 12

Бренд: ifi Страницы: 33

Бренд: Toa Страницы: 1

Symbilink Z100C2-SL

Бренд: zapco Страницы: 18

Бренд: A3D Страницы: 24

Бренд: Soundigital Страницы: 15

FP10 - SCHEMA 1

Бренд: PRESONUS Страницы: 30

Бренд: LD Страницы: 56

Бренд: Anthem Страницы: 12

XXRK-630SP4-14SG-ST4

Бренд: J&M Corporation Страницы: 9

Бренд: Vitus Audio Страницы: 4

Бренд: Zeck Audio Страницы: 14

Бренд: Inline Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды