manualshive.com logo in svg

GRASS VALLEY 8910ADA-M -, Инструкция по эксплуатации

Поделиться
Скачать
GRASS VALLEY 8910ADA-M - Скачать руководство пользователя страница 12

12

8910ADA-M/ST/SR — Instruction Manual

Installation

 

8900 module slots are interchangeable within the frame. There are 10 
three-terminal connectors and 4 BNC connectors in each slot’s I/O group. 
The functional assignment of each connector in a group is determined by 
the module that is placed in that slot. The maximum number of modules an 
8900 frame can accept is ten. 

Figure 2

 illustrates the rear connector plate for 

an 8900 Series Audio frame.

Figure 2.  8900 Series Audio Frame Rear Connectors

To install a module in Gecko frame:

1.

If using local onboard controls, set jumpers on the module circuit 
board. Refer to 

Onboard 8910ADA-M and -ST Configuration

 on page 22

 

or 

Onboard 8910ADA-SR Configuration

 on page 24

 before installing the 

front module.

2.

Insert the module, connector end first, with the component side of the 
module facing to the right and the ejector tab to the top.

3.

Verify that the module connector seats properly against the backplane.

4.

Press in the ejector tab to seat the module.

8156_02

J1

J3

J5

J7

J9

J2

J4

J6

J8

J10

J11

J13

J12

J14

IN

1

J1

J3

J5

J7

J9

J2

J4

J6

J8

J10

J11

J13

J12

J14

IN

2

J1

J3

J5

J7

J9

J2

J4

J6

J8

J10

J11

J13

J12

J14

IN

3

J1

J3

J5

J7

J9

J2

J4

J6

J8

J10

J11

J13

J12

J14

IN

4

J1

J3

J5

J7

J9

J2

J4

J6

J8

J10

J11

J13

J12

J14

IN

5

J1

J3

J5

J7

J9

J2

J4

J6

J8

J10

J11

J13

J12

J14

IN

6

J1

J3

J5

J7

J9

J2

J4

J6

J8

J10

J11

J13

J12

J14

IN

7

J1

J3

J5

J7

J9

J2

J4

J6

J8

J10

J11

J13

J12

J14

IN

8

J1

J3

J5

J7

J9

J2

J4

J6

J8

J10

J11

J13

J12

J14

IN

9

J1

J3

J5

J7

J9

J2

J4

J6

J8

J10

J11

J13

J12

J14

IN

10

Содержание 8910ADA-M -



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды