Screen structure diagram
Ⅱ.Functions and Instructions
This product has three control methods
a. Manual cycle button
b. 12V trigger control
c.R
F
remote control
a.Manual cycle button
The manual cycle button is set on the end cover of
the power supply side of the shell. Pressing the
button will control the screen to rise, stop, fall,
stop, and rise repeatedly. Continuously loop.
b.12V trigger control
Connect the screen trigger hole and projector trigger hole
with a 12V trigger cable; the screen synchronizes the opening
and closing of the projector (that is, when the projector is
turned on, the screen is automatically turned on; when the
projector is turned off, the screen is automatically turned off)
Connecting parts
Tab tension
Fabric
Door
End Cap
Casing
Fabric support bar
Upper support arm
Joint
Lower support arm
Side View
c. RF remote control
●Press the up button, the decorative door opens first, and the fabric rises;
●Press the stop button, the decorative door or fabric will paus
●Press the down button, the fabric rolls back, and the decorative door is closed.
●Jog the up key and down key, the fabric moves up or down;
Usually used in electronic stroke positioning settings.
■
wireless remote 1pcs
Disconnect the screen power supply for 10 seconds and then reconnect
it to the power supply. Press the remote control up and stop buttons
simultaneously within 10 seconds, and the motor will rotate forward and
backward once, and the code matching is completed. The code deletion is
the same as the code pairing operation, the odd time is the code pairing, and the even time is the code deletion.
Code pairing/deleting code
(code pairing has been successful at the factory):
Intelligent electronic itinerary positioning (this product can realize the screen unfolding itinerary setting through the remote
control)
Operation method (stretch a paperclip into the hole, press the positioning setting button on the back of the remote control):
Screen unfolding stroke setting: positioning setting key (lighted) → remote control up and down to the desired position → stop
→ positioning setting key (light off) → location record successful
UP
STOP
DOWN
JOG UP
JOG DOWN
Positioning setting key
AC123Wireless remote control
Paper clip
71
98
145
Power jack
side handle
Manual cycle button
IR jack(φ3.5）
12V trigger jack(φ2.5）
Stop
Stop
Up
Down
Manual cycle
Manual cycle button
12V trigger jack
Projector
IR JACK(φ3.5)
Flexible door opening and
closing device
Accessories
■
Power cable 1pcs
■
12V trigger cable 1pcs
■
Adjustment key(4mm) 1pcs
■
Brush 1pcs
■
Adjustable Mounting Bracket 2pcs
■
User manual 1pcs
■
Hexagonal wrench 1pcs
■
M5X14mmCombination
screw 6pcs
■
M5X10mm screw 10pcs
■
ø5X40mmRound head self-tapping screw 10pcs
Plastic expansion tube 10pcs
Ⅰ.Screen Installation Guidelines
a.
1.Measure the size of the screen, calculate the installation
position of the screen;
2.Mark the installation line at the bottom of the casing. Take
the adjustable mounting brackets, with a symmetrical spacing
of 1600 mm of the center line
3.Stick a flat marking line on the top to mark the positions of
the four screw holes
b.
1.Drill the holes and drive the expansion tube.
2. Place the adjustable mounting brackets vertically, align the
screw holes, and tighten the ø5*40 self-tapping screws.
Ⅰ/a-b
Top
center line
Marking line a
t the bottom of the
casing
Ⅱ
/a-b
Ⅱ
/c
Wall or Cabinet
a
b
Ⅰ/c-d
c. Keep the power supply side to the left, gently place the screen on the bracket, align the bottom rivet nut with the hole on the
bracket, and screw on the M5X14 combination screw, adjust and fix the screen left and right to a suitable position, and tighten
the screws to fix the screen.
d. Connect the power supply and fully unfold the fabric; observe the angle between the fabric surface and the wall, and use the
hexagonal wrench to rotate the hexagonal adjustment screws on the two mounting brackets; after fine-tuning the inclination of
of the screen.
the fabric surface to the best, tighten the machine screw on the screw sleeve to fix it Angle, complete the installation and adjustment
Note:
Installation methods ①②, b mounting plate is not used and can be removed. Installation method ③④ First, fix the b
mounting plate on the screen shell with M5x14 combination screws, and then put the fabric lightly on the a mounting plate
and then lock the connecting screws between the a and b plates.
Remove the 4 screws to remove the b
mounting plate (This mounting plate
can be selected according to the specific
installation method)
Installation ①
Installation ②
Installation ③
Installation ④
Adjustable±1.5°
Adjustable±1.5°
Adjustable±1.5°
Adjustable±1.5°
Fixed Angle
cabinet
cabinet
M5X14mm
Combination screw
■
USB to ø3.5 mono cable 1pcs
