background image

USE  AND  CARE  INSTRUCTIONS

33

    WARNING

!

!

California Proposition 65
The  electrical  supply  cord  and  plug  of  the  rotis-
serie contain chemicals, including lead, known to
the State of California to cause cancer, and birth
defects or other reproductive harm. Wash hands
after handling.

To protect against shock hazard risk, connect  only
 to properly Grounded Outlet.

    CAUTION

!

!

To protect against electrical shock, do not immerse
electrical cord, plugs or motor in water or expose to
rain. Protect electrical elements from burners, hot grill
surfaces and grease.

    WARNING

!

!

CORRECT TRANSFORMER AND LIGHT USE

Read  all  instructions  before  initial  use.
IMPORTANT:  When  using  transformer  appliances,  basic
safety  precautions  should  always  be  used.
The  Transformer  is  set   for  120V,  60Hz  AC  current  input,
12VAC, 25W output. The Light is set for 12V, 10W.
Do  not  let  children  operate  or  play  nearby  your  grill  or
Transformer. Always supervise children and pets if they are
in the vicinity of the unit.

Connecting Transformer

Always attach  the assembled Transformer  to your  grill first
and then plug the Cord into a properly grounded outlet, then
turn  on the  Lights.

Operating Transformer and Light

Do not operate the Transformer if the cord or plug becomes
damaged,  or  if  the  Transformer  or  Light  malfunctions  or
have  been  damaged  in  any  manner.
Do not operate the Transformer if the cord or plug has been
damaged in any manner. Do not use the Transformer and
Light  if  cannot  be  operated  safely.
Do not immerse Electrical Cord or Plug in water or expose
to  rain,  as  this  may  result  in  an  electrical  shock.

Disconnect Transformer

Be careful as all surfaces will be hot, both grill, Transformer
and  the  Light.  Turn  off  the  Lights  and  unplug  the  Trans-
former  from  electrical  outlet  when  not  in  use  and  before
cleaning.

    CAUTION

!

When using electrical appliances, basic safety
precautions  should  always  be  used.

!

ELECTRICAL  EQUIPMENT  USE

To  protect  against  electric  shock,  do  not  immerse
cord  or  plugs  in  water  or  other  liquid.
Allow  Rotisserie  and  Grill  to  cool  before  putting  on  or
taking  off  parts.
Do  not  operate  any  outdoor  cooking  gas  appliance
with  a  damaged  cord,  plug,  or  after  the  appliance
malfunctions  or  has  been  damaged  in  any  manner.
Call  1-877-934-7455  for  repair.
Do not let the cord hang over the edge of a table or
touch  hot  surfaces.
Do  not  use  an  outdoor  cooking  gas  appliance  for
purposes  other  than  intended.
When connecting, first connect plug to the outdoor cook-
ing  gas  appliance  then  plug  appliance  into  the  outlet.
Use  only  a  Ground  Fault  Interrupter  (GFI)  protected
circuit  with  this  outdoor  cooking  gas  appliance.
Never  remove  the  grounding  plug  or  use  with  an
adapter  of  2  prongs.
Use  only  extension  cords  with  a  3  prong  grounding
plug, rated  for the  power of  the equipment,  and
approved  for outdoor use with a W-A marking.

1.

2.

3.

4.

5.

6.

7.

8.

9.

Содержание OB2610ALP










































Отзывы: