USE AND CARE INSTRUCTIONS
If ignition does not occur in 5 seconds, turn the Control
Knob(s) and gas source OFF and conduct a leak test
as explained in the Use and Care section of this guide.
If no leaks are detected, wait 5 minutes for any gas
to clear and repeat the lighting procedure.
WARNING
!
!
WARNING
!
!
Should a FLASHBACK fire occur in or around the Burner
Tubes, follow the instructions below. Failure to comply
with these instructions could result in a fire or explosion
that could cause serious bodily injury, death, or property
damage.
Shut off gas supply to the gas grill.
Turn the Control Knobs to OFF position.
Open the Grill Lid.
Put out any flame with a Class B fire
extinguisher.
Once the grill has cooled down, clean the
Burner Tubes and Burners according to the
cleaning instructions in this Use and Care
Guide.
Ÿ
Ÿ
Ÿ
16
Never
lean over the grill cooking area while lighting
your gas grill. Keep your face and body a safe
distance (at least 18 inches) from the front of grill
when lighting your grill by match.
WARNING
!
!
TROUBLESHOOTING
If the grill fails to light :
Misalignment of Burner Tubes over Orifices
Correction:
Reposition Burner Tubes over Orifices.
Obstruction in gas line
Correction:
Remove fuel line from grill. Do not smoke! Open
gas supply for one second to clear any obstruction from fuel
line. Close off gas supply at source and reconnect fuel line
to grill.
Plugged Orifice
Correction:
Remove Burners from grill by removing the
screw from the rear of each Burner using Phillips Head
Screwdriver. Carefully lift each Burner up and away from
gas valve Orifice. Remove the Orifice from gas valve and
gently clear any obstruction with a fine wire. Then reinstall
all Orifices, Burners, screws and cooking components.
If an obstruction is suspected in Gas Valves or Manifold,
call the Grill Information Center 1- 800-761-5456
Monday - Friday 8:00am-4:30pm CST
Obstruction in Burner Tubes
Correction:
Follow the Burner Tube cleaning procedure on
page 21
of this Operator's Manual.
Misalignment of Ignitor on Burner
Correction:
Check for proper position of the Electrode Tip
as shown in
steps 5 & 6 on page 11.
The gap between
the Spark Electrode Tip and Spark Receiver should be
approximately 3/16" wide. Adjust if necessary. With the
gas supply closed and all Control Knobs set to OFF, press
the Electric Ignitor cap and watch for the presence of a
spark at the end of the Electrode
Disconnected Electric Wires
Correction:
Inspect the Ignitor Junction Box found behind the
Control Panel. Connect loose Electric wires to Junction Box
and try to light the grill.
Weak AA battery
Correction:
Remove the Ignitor Cap and replace the bat-
tery.
If the grill still does not light you may need to purge
air from the gas line or reset the regulator excess gas
flow device.
Note:
This procedure should be done every
time a new LP Gas tank is connected to your grill.
Turn gas off at source and turn Control Knobs to OFF. Wait
at least 5 minutes for gas to clear, then retry.
If your grill still fails to light, check gas supply and
connec tions.
Repeat lighting procedure. If your grill still fails to oper-
ate, turn the gas off at source, turn the Control Knobs to
OFF, then check the following:
1.
2.
3.
To light your gas grill by match, insert a match into the
Lighting Stick and follow steps 1 through 5 of the Grill
Lighting Instructions. Then, light the match and place Light-
ing Stick through the Cooking Grids on the grill (See Dia-
grams Below). Turn the correlated Control Knob to the
IGN/HIGH setting to release gas. The Burner should light
immediately.
Manually Lighting Your Grill By Paper Match
Ÿ
Ÿ
Match
Lighting
Stick
To purge air from your gas line and/or reset
the regulator excess gas flow device:
Turn Control Knobs to the OFF position.
Turn off the gas at the tank valve.
Disconnect regulator from LP Gas tank.
Let unit stand 5 minutes to allow air to purge.
Reconnect regulator to the LP Gas tank.
Turn tank valve on SLOWLY 1/4~1/2 of a full turn.
Open the Grill Lid.
Push and turn the Right Main Burner Control Knob
to IGN/HIGH.
Press Electric Ignitor for 3-4 seconds to light the
burners.
