Graco XM Series Скачать руководство пользователя страница 28

Страница: 28 / 106

Troubleshooting

313289W

Paint does not cure consistently.

Ratio not set correctly.

Check that correct ratio is set and set by
volume. See XM sprayer operation manual.

Material not mixing correctly.

Test pump. Make sure mixer is clean; flush as
needed. See XM sprayer operation manual.
Position mixer after integrator hose.

Material not properly conditioned
before it was added to sprayer.

Mix material thoroughly.

Not using enough integration hose.

Add more integration hose.
Select “fast dosing” in setup.

Poor spray pattern.

Fluid pressure too low.

Increase pump pressure.

Fluid temperature too low.

Increase fluid temperature.

Spay tip dirty or worn.

Relieve pressure. Clean or replace tip. Follow
gun manual instructions.

Fluid A and B fitters plugged.

Clean filters. See pump manual.

Mixer hoses partially plugged or too
restrictive.

Inspect parts for cured material. Clean or
replace, or use larger hoses and mixer.

Problem

Cause

Solution

Содержание XM Series











































































































Результаты поиска

Содержание XM Series

Отзывы:

Бренды по названию

Популярные бренды

Graco XM Series, Запасные части

Результаты поиска

Содержание XM Series

Отзывы:

Бренды по названию

Популярные бренды