background image

Warning

309524L

5

EQUIPMENT MISUSE HAZARD

Misuse can cause serious injury or death.

For professional use only.

Use equipment only for its intended purpose. Call your Graco distributor for information. 

Read manuals, warnings, tags, and labels before operating equipment. Follow instructions.

Check equipment daily. Repair or replace worn or damaged parts immediately.

Do not alter or modify equipment. Use only Graco parts and accessories.

Do not exceed the maximum working pressure or temperature rating of the lowest rated system 
component. See Technical Data in all equipment manuals.

Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all 
equipment manuals. Read fluid and solvent manufacturer’s warnings.

Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces. 

Do not use hoses to pull equipment.

Comply with all applicable safety regulations.

BURN HAZARD

This equipment is used with heated fluid, which can cause equipment surfaces to become very hot. To 
avoid severe burns: 

Do not touch hot fluid or equipment.

Allow equipment to cool completely before touching it.

Wear heat protective gloves and take special care if fluid temperature exceeds 110°F (43°C).

TOXIC FLUID OR FUMES HAZARD

Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or 
swallowed.

Read Material Safety Data Sheets (MSDS) to know the specific hazards of the fluids you are using.

Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.

PERSONAL PROTECTIVE EQUIPMENT

You must wear proper protective equipment when operating, servicing, or when in the operating area of 
the equipment to help protect you from serious injury, including eye injury; inhalation of toxic fumes, and 
hearing loss. This equipment includes but is not limited to:

Protective eyewear 

Gloves, clothing, and respirator as recommended by the fluid and solvent manufacturer

Hearing protection

WARNING

Содержание VISCON HP 245848































Отзывы: